Jämä Blanket Shirt from Varusteleka

A clothing item you see on a lot of bushcraft-oriented sites is a blanket shirt. Basically, they are hoodies made from old wool blankets. They are favored for a few reasons: wool retains warmth even when wet, wool is safer around an open campfire than synthetic fabric, when hunting it's very quiet if it brushes up against something, and if in muted colors blends in with the woods well. And let's face it, blanket shirts fit the bushcraft aesthetic well.

Blanket shirts can be homemade or purchased. YouTube has numerous videos on making your own.

Perhaps the best known commercially available blanket shirt is the Boreal Shirt from Empire Canvas Works or Lester River Bushcraft. They are premium pieces of clothing and priced accordingly.

If your budget doesn't permit spending the money for a Boreal Shirt, or if you want to try out a less expensive factory-sewn option check out the Jämä Blanket Shirt from Varusteleka. They are sewn in Varusteleka's factory in Helsinki, Finland.

Varusteleka currently lists two variants, one made from H.R. Co. blankets, while the other is made from Finnish suplus wool cloth that was used for their M/65 uniforms.

A couple weeks ago I bought one in the Finnish wool, and I used it for the first time on my recent deer hunting trip while hanging out in our cold cabin. I wore it over a Hill People Gear long sleeve base layer, a flannel shirt, and an Orvis fleece and wool vest. I was warm in the cabin where the temps were in the low 30s. It wasn't very windy outside and the Jämä shirt kept me warm when I stepped outside for a few minutes to take a leak. If you're going to wear this in windy conditions, you're going to want a shell over top of it, however. A suitably sized windproof smock would be just the ticket.

For size reference, I am about 5'5" with an 18" neck, 32" sleeves, a 45" chest, 48" gut (ugh), and normally wear an XL or 2XL, depending on the item of clothing or a brand's sizing. The Jämä Blanket Shirt that I bought is a 3XL. (Pay attention to Varusteleka's sizing guidelines.) Since the garment does not stretch and you need to pull it on, it needs to be big, especially if you have any layers on.

The sleeves are 35" long, so they cover up my hands. I can roll them up if I am working.

Obviously, this is not something I'd wear about town. If I'm out in the woods I don't care if I look like a wannabe Jedi or I'm on my way to Mordor.

The hood is a bit floppy. In the picture I am wearing a ball cap under it, which keeps it out of my eyes. It's deep enough to provide protection against wind from the side and to help create a warm air bubble in front of your face.

As shown in the pictures, it has a kangaroo pocket, hood, and the back is longer than the front. I like the vertical placement of the front pocket, which is large enough to comfortably hold my keys, a pair of rag wool gloves, and my iPhone 7 Plus.

There is a smaller pocket inside the kangaroo pocket. You could put a folding knife in there but I don't see myself getting much use out of it. It's not large enough for the iPhone 7 Plus.

The stitching is good quality. There were no loose threads. The wool fabric is a bit nicer than an old military surplus blanket, which makes sense since it was actually intended for use in making clothing. It's about the same weight as the old USGI M-1951 wool field shirts but not as scratchy.

It's a good, basic hoodie. Compared with the Boreal Shirt it lacks some features. E.g., a draw cord on the hood, an adjustable collar, and snaps or straps to cinch down the wrists. However, the Jämä shirt also about 1/3 the cost. If you have moderate tailoring skills you could customize it.

Do I recommend the Jämä wool blanket shirt? Yes, if the sizing and feature set work for you. IMO it would be great for bow hunting with temps in the 30s or 40s.

Cold Weather Camping and Equipment Failure

Last weekend my daughter and I, along with a friend went up to Tioga County to catch the last two days of Pennsylvania's rifle deer hunting season. My friend's land is about 12 miles south of the New York line. Our plan was to go up Friday, get a couple hours of hunting in that afternoon, then hunt Saturday, and then come home Sunday. For shelter we'd be using my friend's primitive cabin.

The cabin has no utilities and the off-grid solar project is not yet complete. For heat, we planned to rely on my Dyna-Glo 23,000 BTU kerosene heater and my friend's propane-fired patio heater. We've used the latter in the past and it's worked well.

My previous use of the kerosene heater was at home for space heating and for that it worked great. We haven't used it in a few years so I made sure to replace the two C batteries that power the igniter before we left. After we got onsite I filled the tank and let it sit for about an hour for the wick to soak up some fuel. It fired right up on the first try. Note that the K-1 kerosene I had was a few years old but still in the original, sealed 4 gallon can. When stored properly, K-1 has a long shelf life.

Unfortunately, this time the propane heater was not working, due to a failed or clogged regulator. My friend is a mechanical engineer by profession and no matter how we tried to clean, defrost, or clear it, we could not get sufficient gas to flow to the burner element of the heater.

The cabin is 16' x 24' with an uninsulated metal roof with a ridge vent. The kerosene heater was able to take the edge off but inside it still hovered around freezing, even before dark.

Friday night the temp was forecast to get down to about 20F (-6.7C). We all had sleeping bags up to the task but being out and about in the shelter wasn't so great.

We borrowed a Big Buddy propane heater from a neighbor, which we used while sleeping.

Overnight, the temp inside the cabin got down to about 30F (-1C). I was warm enough in my Kelty Cosmic Down 20 bag, which was inside my Jerven Thermo Hunter, but I couldn't get a good night's sleep. I found the Kelty mummy bag too constraining.

The forecast for Saturday night was 15F (-9.4C). We decided to hunt Saturday morning but pack up and head home after lunch. These temps may seem mild to my more Northern readers, but when you live in Southeast PA and are not acclimated, they are draining when you can't get inside and warm up.

Lessons learned:

• The kerosene heater was awesome, easy to use, and took off the edge. Unfortunately, it was not enough to make the cabin comfortable.
• The regulator on the patio heater may have been clogged. It may have helped had it been wrapped in a plastic bag and taped shut to keep bugs out.
• It would have been a good idea to test it the last time someone was upstate, in warmer weather.
• We really need to get a wood stove installed. My friend has one but it's not there, it's still at his house downstate.
• We need to work on sealing up some of the drafts in the cabin and maybe rigging a tarp across it inside, to keep warm air lower, instead of escaping through the ridge vent.
• I need a different cold weather sleeping bag. The Kelty is warm enough but to constricting. My daughter used my USGI MSS and was happy as a clam with it. I may pick up another one but I am also considering something like a 0-degree down backpacking quilt from Enlightened Equipment. I could throw it on top of my Hill People Gear Mountain Serape or Wilderness Innovation Osni Cloak, either of which can be used as a quilt or rectangular bag. Reader input is welcome.

What's in Your Parka

Over at American Grouch, Cro has an interesting article on what he carries in his parka pockets when out and about in extremely cold weather (i.e., sub-zero Fahrenheit).

Check it out.

15 Uses for a Triangular Bandage

A nice article over at Primal Survivor about medical and non-medical uses for triangular bandages:

https://www.primalsurvivor.net/triangular-bandage-uses/

October 2018 Overnight Camping Trip

Polymer 80 Range Report

I shot the Polymer 80 "Glock 19" last night. My dad and I put about 150 rounds through it, mostly Herter's 115 grain ball (made by Sellier & Bellot), along with around 25 rounds of my handloads. They were 115 grain Berry's plated bullets on top of 4.5 grains of Universal Clays in mixed brass.

The gun had one malfunction, a failure to fully go into battery with one of the handloads. Previously, I had some issues with this batch in my CZ P-09. AFAIC it was an ammo issue, not a gun issue.

Accuracy was OK, nothing to crow about. Most of the rounds went into a palm-sized group at 7 yards. The limiting factor for me was the trigger. Even with my fluff and buff job it is still pretty bad -- heavy and creepy. I'll see what it feels like after 500 rounds but if there isn't a marked improvement I'll look into getting something like an Apex trigger.

The other mod I have tentatively planned is a set of Heinie Straight Eight night sights.

After I finished shooting I field stripped it and saw no signs of unusual wear.

So far I'm very pleased with the gun.

Polymer 80 Build Complete

I finished up the Polymer 80 "Glock 19" today. Impressions:

1. "Milling" the frame is easy. I used end nippers to remove most of the excess rail material, then filed and sanded them smooth.
2. Assembly gave me some issues but mainly because this is my first "Glock." In particular, I had issues getting the slide stop in correctly so that it would either turn the gun into a single shot, or fail to raise at all. But I got it squared away.
3. The "$0.25 Glock trigger job" is worth it. Before I polished several parts in the mechanism, the trigger pull was really heavy and gritty. Now it's a lot better and should smooth up with use.
4. The Polymer 80 grip is an improvement for me over the stock Glock 19 grip.

I am left handed and found that the magazine catch rubbed on my middle finger uncomfortable, so I beveled the offending corner.

Not being a fan of the hole in the bottom of the grip behind the magazine well, I added a Strike Industries grip plug, which holds a combo flat head screw driver/punch, and a small oil vial. It had to be sanded a bit to allow magazines to drop free. Speaking of which, I bought four MagPul P-Mags from MidwayUSA to go with the gun.

I'm hoping to shoot it tonight on an indoor range. Range report to follow.

80% Glock Build

We've done 80% AR15s, so now it's time to build a Glock 19 from an 80% lower. Like with AR15s, this isn't about saving any money, it's more about flipping the bird to the man. You can pick up a perfectly serviceable used Glock for the same or less money.

I'm on a zillion lists already so blogging about this isn't going to make a difference for me.

Aside from that, it will be a great learning process so I know how Glocks work from the inside out. Glocks are among the most common handguns available so that's a good thing.

What's really neat about this is that because the receiver is plastic, it can be done entirely with hand tools. I've read of guys completing one of these in a half hour. That said, I plan to take my time and get it right.

Another nice thing from my perspective is that the Polymer 80 frames fix the uncomfortable-to-me Glock grip angle (the main reason I don't own a Glock).

The frames are compatible with OEM Gen 3 Glock parts, or aftermarket Gen 3 Glock parts. Gen 4 or 5 parts do not fit. Gen 1 or 2 may fit but Gen 3 is specified for these frames.

Links:

• Polymer 80, maker of the 80% lowers (also has polymer AR15 lowers).
• Nice article on Pew Pew Tactical detailing the build process with lots o' pictures.
• Massive thread on Arfcom with tips, notes about pitfalls, and pics of a bunch of builds.
• Another useful Arfcom thread.

The Polymer 80 kits and assorted parts are available from various online vendors including MidwayUSA and Brownells. However, I didn't want to have to source all the parts to complete the build separately, so I went to 80P Builder and ordered a "Ruiz Package" which includes the 80% frame, lower parts kit, and an assembled barrel/slide assembly. This package was a special and is now out of stock. (Fred Ruiz is a pro shooter/ex-SEAL sponsored by 80P Builder.)

Pic of the kit I ordered:

(Picture borrowed from 80P Builder.)

The kit does not include a magazine and 80P Builder only has ETS mags in stock, so I ordered 4 MagPul Glock 19 P-Mags from MidwayUSA. (I don't know how good the ETS mags are. They may be just fine.)

Note: The frame has a metal plate molded in so that if you want or need to add a serial number, you can do so. E.g., California builders can request a serial number from the CA DOJ for their gun to stay within the bounds of state law. This is not required on a Federal level. In my opinion, putting some kind of serial number on the gun is a good idea if for no other reason than identification if you need to file a police report for a stolen gun.

Polymer 80 also sells frame kits for Glock 17 and 26 size guns. While mine will be in 9mm, AFAIK you could build one in .40 S&W or .357 SIG as long as you get the correct parts. They also work with Advantage Arms .22LR conversion kits. Polymer 80 is supposed to be introducting G20 / G21 sized frames later this year, for those interested in a 10mm or .45 ACP build.

I got a shipping notice from 80P Builder this morning. They are located in Charlotte, NC, so I expect to have it by the end of the week.

Updates to follow.

How to Make and Use a Stropping Block

Work Sharp Guided Field Sharpener Review Video

New Sights for the Rossi 92

My 14 y/o daughter wants to join me deer hunting this year so I needed something she could shoot well with mild recoil. The Rossi 92 in .357 Magnum I bought several years ago fits the bill, but I wanted to improve her hit probability, which meant mounting an optic.

As a copy of the Winchester 1892, the Rossi 92 is a top-eject design, which complicates optic mounting. You need to either find some kind of a mount offset to the side or use something with long eye relief mounted on the barrel.

Rossi drilled and tapped the barrel for a scope mount. The holes are covered up by the open rear sight, which must be removed to use them.

NOE Bullet Molds makes a very nice Picatanny rail that fits the Rossi. I ordered one and received it in a few days. Before installing it, I degreased the mounting holes in the barrel using denatured alcohol, and put a drop of thread locker on each screw.

The optic I chose was a Bushnell TRS-25 red dot sight. Since my Rossi is in .357 I view it as a 75 yard deer rifle. A non-magnified optic is fine for such ranges.

I have a few other TRS-25s and they've all been very good, with clear lenses, a well-defined dot, and rugged. As a micro-dot sight the TRS-25 hardly affects how a rifle feels. Finally, they are low-priced. I got this one for $45 shipped on Amazon Prime. (I just checked Amazon and it's now listed for $43.24.)

Because the NOE rail required removal of the rear sight the gun is left without backup irons if your optic tanks. So, I ordered a bolt-mounted peep from Steve's Guns. When I first bought the carbine I installed one of his safety replacement plugs. I wish I'd just gone straight to his very slick peep sight.

The resulting package is still light and handy with plenty of firepower, but vastly improved low-light shootability.

Last weekend I took my kids camping and my daughter got to put 50 rounds of Fiochi .357 Magnum 158 grain JHPs through the Rossi. Without zeroing the RDS on paper, she was easily able to keep her shots on a 10" gong, shooting rapidly offhand at 25 - 30 yards.

We're hoping to get to the range next weekend so she can get some more practice in and so we can zero the Bushnell.

The final touch to ready the Rossi for hunting season will be to add quick-detach sling swivel studs and a sling.

Homemade Apple Chips and Beef Jerky

We've had a Nesco food dehydrator gathering dust in the kitchen since last year. Yesterday, Amanda and I finally put it to use.

We first made a batch of apple chips. To make them, we cored a half dozen apples, sliced them about 1/4" to 3/8" thick, and then dipped them in lemon juice to prevent browning. Then they went into the dehydrator at about 140 degrees F. for 4.5 hours.

I should have gotten picture of the apple chips, but they lasted all of 10 minutes after coming out of the machine. They were awesome.

While the apples were drying we sliced up 6 chuck steaks and marinated them with seasoning that came with the dehydrator. After the apples were done we put the beef in and let it run overnight, about 12 hours at about 160 degrees F.

I took it out this morning. It's really damn good and a lot cheaper than store-bought beef jerky. For around $16 worth of beef I probably got about $50 worth of jerky, had I bought it at the supermarket.

The dehydrator came with 5 trays and will work with up to 12. This morning I ordered two more trays along with a package of the Nesco jerky seasoning.

As an aside, the dehydrator is not too noisy. It was audible from the next room but was basically a low-level white noise.

Making the apple chips and jerky was time-consuming but worth it. I'd like to see us get into using the machine a lot more because the home made dehydrated items are a lot cheaper than those bought in the store.

Homemade Bug Repellent

There are plenty of over-the-counter insect repellents that work well. Most of them used DEET (PDF file from the US Centers for Disease Control) as the active ingredient. I've used various DEET-based repellents for years with good results.

You do have to be careful with DEET, however, since it will dissolve plastics. For example, it can damage watch faces and poly-based gun stock finishes. If you use a spray, make sure you do it where overspray won't hit plastics, including those on vehicles. Further, some people may be sensitive to it and it is toxic if ingested.

Permethrin treatments for clothing are also very useful but you should not use them directly on your skin.

I've had positive results by using Granpa's Pine Tar soap before heading out to the woods. Pine tar has long been used in insect repellents. In his classic tome from 1884, Woodcraft and Camping, Nessmuk described his formula for bug dope as:

• 3 ounces of pine tar
• 2 ounces of castor oil
• 1 ounce of pennyroyal oil

His directions were to mix them together over a low fire and bottle for use. Pennyroyal oil can have some nasty side effects, so use with care.

More recently, Lars at Survival Russia posted this video:

Lars' formula is:

• 3 parts of beeswax
• 1 part of pine tar
• A little cooking oil, e.g., olive oil or canola oil (to make it more spreadable)

Last week, I decided to give Lars' recipe a try. I melted the ingredients together in a Pyrex measuring cup on a hot plate, and poured the resulting mixture into Sho-Ka-Kola tins.

(While I had the hot plate out, I decided to finish pan lubing my last batch of .44-40 bullets.)

I'm interested to see how well the pine tar-based bug dope works. By the smell, it should repel people just fine. Pew!

It can also be used as a leather dressing, making it multi-use. I have a camping trip coming up and plan to test out this bug dope. I'll post a report afterwards.

Made a Stropping Block

Today one of my friends on Facebook posted a link to an article on the A.G. Russell Knives website,
How to Make a Finishing Paddle.

Coincidentally, yesterday I put together my first stropping block/finishing paddle with a piece of leather glued to a piece of wood. Even though I've been sharpening knives for close to four decades, I only started using a strop in the last couple of weeks. I immediately noticed a difference in my knife edges.

That's been a real oversight on my part, because a strop can help you get a really sharp edge on a knife, and polish the bevel, which has a couple benefits. First, it reduces drag in the cut, and second, it makes the edge a little more corrosion-resistant because the smooth surface is less prone to retaining moisture.

Some pictures. First, the stropping block before I applied any compound.

Second, after applying the green compound from Eastwood. As you can see, it didn't go on evenly. I should probably have sanded the block to ensure it was as level as possible, and then sanded the leather also. Oh well, it's a learning process.

Finally, what it looks like after a little use. The dark spots are where it removed metal from the knife.

It may not look like much but it helped get a few of my knives really sharp. E.g., my Cold Steel Bushman feels like a razor now.

I made this one from some cowhide I had laying around that was about 1/8" thick, and a piece of a scrap 2x4. The thick base helps provide clearance so you don't hit your knuckles on your workbench.

I may go back and tweak it by scraping off most of the compound, adding some mineral oil to the leather, slightly roughing the leather so it takes the compound better, and then reapplying the compound.

My brother requested that I make him one and I'll use the lessons learned with this one in doing so.

If you don't have the materials for making one yourself laying around like I did, and want to try using a stropping block, you can get one off Amazon, here.

Camillus TL-29 Electrician's Knife

I picked up this old Camillus electrician's knife off eBay for a whopping $11.50 shipped.

Generations of American servicemen have known this style of knife as the "TL-29." They were typically paired with a set of linesman's pliers and leather belt pouch to hold both items. Below is a picture I found on Pinterest, apparently scanned from a US military manual.

Used TL-29s can be found on eBay for little money and newly-made ones are available from Klein and other manufacturers.

According to the tang stamp guide found here, the knife was made between 1960 and the late 1970s.

It showed signs of use and some neglect, but no outright abuse. E.g., it was dull, dirty, and had some rust which I removed by an overnight soak in Evaporust. The blades snap into position nicely with positive half-stops and no side-to-side wiggle. The brass liner lock positively keeps the screwdriver in the open position.

As I received the knife it was very dull but now it's shaving sharp. It took about an hour's worth of work on my DMT fine diamond bench stone and Worksharp Field Sharpener combined to put a good edge on it.

I plan to keep the edge on the screwdriver blade relatively dull for use as a scraper; it was originally intended as such and as a wire stripper. I expect it to throw sparks from a ferro rod rather well.

Worksharp Field Sharpener

In the past couple of weeks I’ve been on a cutlery buying binge. I received a nice Amazon gift card for my birthday at the end of May, and among the items I bought was a Work Sharp Field Sharpener.

The Worksharp Field Sharpener is an impressive little piece of gear for maintaining knives in the field or at home. It comes with coarse and fine diamond plates, a ceramic stick for honing, a small ceramic stick for working on serrations, and a leather strop. Built into the unit are guides to help you set the correct angle when using all of the sharpening bits.

Since receiving the Worksharp I’ve used it to touch up several pocketknives both old and new, and it’s enabled me to put shaving-sharp edges on them while sitting in my recliner.

The overall length is a bit under 7 inches, so it’s best used on smaller knives. Of course, you can use it on larger blades but you’ll need to work on shorter sections of the edge at a time. For scale, here it is next to an old Camillus TL-29 electrician's knife:

I plan to take the Worksharp with me on camping trips as my field edge maintenance solution. I might even get a second one to leave in my camping toolbox.

Improving the Heavy Cover USGI Canteen Cup Lid

Last year I bought a stainless steel lid for my USGI canteen cup from Heavy Cover, Inc. (It doesn't seem to be listed there currently.) I haven't gotten much use from it for two reasons:

1. It's too heavy for what it is.
2. It was a very snug fit in the cup.

Today I decided to improve it with the help of Mr. Dremel, but cutting away part of the lip that sits inside the cup.

First, here it is being held by its handle in my vise. I've already made one cut with my Dremel using a heavy duty cut-off wheel.

After making the cuts, I snapped the excess material off with pliers. Then I used a grinding stone in the Dremel to deburr where I made the cuts.

And finally, sitting on the cup. As you can see, it's the older L-handle style. IMNSHO, this is much better than butterfly handles. If you look closely you can see where I added graduation markings to the cup.

The lid is a bit lighter now but it would have been better had it been made from hard anodized aluminum, or at least a thinner gauge of stainless steel. It's noticeably easier to set on the cup or remove it to check how something is cooking.

DIY Adjustable Pot Bail

For cooking, or even just boiling water over an open fire, a pot with a bail is really handy. However, bails add weight and bulk and we often already have a good pot that just needs a bail sometimes. Over on Bushcraft USA, "Jerome" posted a great how-to thread here.

If video is more your style, Lonnie posted a video inspired by the above thread on his YouTube channel, Far North Bushcraft and Survival.

Most hardware stores should have the required materials. I bought 6 feet of 1/16" cable and the appropriate ferrules today at Home Depot for around $6. (That included an extra set of ferrules.)

I made up a couple bails this afternoon, each from a 3' piece of cable. After crimping the ferrules similarly to how Lonnie did in the above video for the first bail, I took a slightly different tack for the second bail. I hit each ferrule with a punch once to hold it in place on the end of the cable, I then used my bench vise to fully crimp it.

The advantage of using the vise is that you get a full-width crimp, not just where you hit it with the punch.

My plan is to keep one bail with my Keith Titanium canteen and cup set, and the other with my old USGI canteen cup.

Ten Medical Uses for a Triangular Bandage

This video discusses 10 medical uses for a triangular bandage.

{Hat tip to Greg Ellifrtiz.}

Aside from medical uses, triangular bandages can be used for many of the same things as a shemagh or bandana. For example:

• Dust mask
• Hankerchief
• Head scarf
• Sweat band
• Scarf to keep your neck warm, or cool if you wet it.
• Pre-filter for water, to keep your filter from getting clogged with chunky bits.
• Pot holder
• Pot scrubber
• Wash cloth
• Etc.

I always carried a couple USGI muslin triangular bandages when I was in a Civil Air Patrol ground search and rescue unit, as did my team members. 

Turning Components Into Ammo

Over the past few weekends I have been busy turning components into ammunition. I dipped into my stash of empty .38 Special brass and loaded up several different varieties:

• 50 rounds of 178 Keith semiwadcutters (SWC) on top of 3.8 grains of Unique.
• 50 rounds of 178 Keith SWCs on top of 5.0 of Unique.
• 100 rounds of 195 grain lead round nose bullets (LRNs) on top of a 5.0 grains of Unique.
• 100 rounds of 148 grain Lee tumble lube wadcutters on top of a 2.7 grains of Bullseye.
• 100 rounds of 148 grain Hornady hollow base wadcutters (HBWC) on top of 2.7 grains of Bullseye.
• 100 rounds of Speer 158 grain lead SWC hollow points on top of a 4.5 grains of Universal Clays.

DO NOT USE ANY OF THE ABOVE LOADING DATA WITHOUT VERIFYING IT IN ONE OR MORE LOADING MANUALS!!! I AM NOT RESPONSIBLE FOR ANY DAMAGE THAT OCCURS TO YOU OR YOUR GUNS IF YOU RELY ON IT.

The Keith SWCs, 195 grain LRNs, and Lee TL WCs came from Matt's Bullets. I ordered 100 count sample packs of each and was impressed with the projectiles. They are sized to .359 and loaded with Carnauba Red lube, except for the 148 TL WCs, which appear to be lubed with Lee Liquid Alox.

I was quite pleased with the service from Matt's Bullets, BTW. My order shipped in about a day and a half and was sent in a USPS flat-rate box. I received 2 days after I got the shipping notice. The bullets all looked good.

The Hornady 148 grain HBWCs have been laying around since I bought 1250 of them at the end of 2016. I've had the 500 count box of the Speer LSWCHPs for years.

So what prompted this binge reloading? First, the weather has been nice and it has been neither too hot nor too cold to work out in my backyard shop. Second, my gun interests go in phases and  something rekindled my interest in revolvers. It's been too long since I shot one of my K-Frames, S&W Model 28, or 50th Anniversary Ruger Blackhawk.

And frankly, the state of the political left in this country is really starting to worry me. As far as I'm concerned, they've been acting completely batshit crazy since Trump's election. I want to get in some more practice in case the left decides to take their attempt at a soft coup hot.

I was pleasantly surprised that the .38s loaded with the Keith SWCs feed well in my Rossi 92 .357 carbine. I'd figured the SWCs might hang up during feeding, but they seem to be held at just the right angle to slip right into the chamber. (Testing was done with 3 dummy rounds, not live ammo.)

I got the 195 grain bullets because I thought it would be neat to try and duplicate the old .38 Special Super Police load, which had a 200 grain LRN at mild velocity. I wound up loading them over enough Unique, though, that they will only be shot in my .357s. If nothing else, they should make steel plates jump around nicely.

The Speer 158 LSWCHP loads should run about 850 FPS from a 4" barrel, very similar to the old FBI load. I can bump the powder charge up a little to get over 900 FPS but at +P pressures. These would be good for defense from any of my K-Frames, and should also work well in my J-Frame S&W Model 640.

To measure the powder charges I used both my Redding Model 3 measure and my RCBS Little Dandy. I don't like how Unique meters in the Redding, although it seems to meter a little more smoothly in the Little Dandy. In contrast, Universal Clays seems to meter very nicely in the Little Dandy -- smooth and extremely consistent. I haven't tried it yet in the Redding but I expect it to behave similarly.

Of course, the proof will be in the shooting of this ammo. I'm hoping to get to the range in the next week or two to dirty up some wheelguns.

Korean Beef Bibim Bap MRE

While checking out foreign MREs on eBay, I ran across the vendor "magnetic1" selling dehydrated beef bibim bap entrees, which are supposed to be Korean-issue. Since I'm always interested in stuff to eat while camping, and I love Korean food, I ordered a 3-pack to try.

Here's the front and back of the package along with the included spoon.

Upon opening, you can see that it's mostly rice with some vegetables. The little brown nuggets are pieces of dehydrated beef. Also shown are the packet of sesame oil and gojang (Korean BBQ) sauce that were inside.

To cook it, you add hot water to the black line inside the bag, seal it, and let it sit for 10 minutes. Or, you can use cold water but you'll need to wait twice as long.

And here's what it looks like after rehydrating and mixing in the oil and sauce packets.

I liked it, it was damn tasty. I used all of the gojang sauce and while it was spicy, it wasn't mouth-burning. That said, I eat Korean food fairly often and eat it full strength, so YMMV. Compared with a couple different Mountain House meals that I've tried, this isn't nearly as salty.

For me, this entree would be enough for lunch but not dinner.

I have two more left that I'm going to save for the field.

Self Sufficiency

Today I cast up about 10 pounds worth of bullets for .44-40, using my Accurate Molds 43-215C mold. I got at least a couple hundred usable projectiles.

You know damn well that the next time the Dems get into power, there will be another panic. How are you preparing against that inevitability?

Black Powder Shotgun Shells in Brass Cases

Note/Disclaimer: This post contains loading data believed to be safe in my guns. It may not be safe in yours. Do your own research before you try this. I'm not responsible if you get hurt or your gun gets damaged.

A couple of weeks ago on Survival Russia, Lars posted a video about loading brass 16 gauge cases using minimal tools. He followed up with a second video in which he shot his reload and got what I considered pretty good results.

In the past I have experimented with hot glue slugs* using minimal tools, and as I've posted about before, I have muzzleloading smoothbores. I also have a few break open shotguns that I've been wanting to try black powder loads in, since I have a good stock of black powder and you can reload brass cases with minimal tools that you can make at home.

So, I put in an order with Ballistic Products, Inc. for a few items, including:

• Two boxes of Magtech empty 2.5" 12 gauge brass shotshell cases, and
• A 500 count bag of 10 gauge over shot cards.

Magtech brass cases have a larger internal diameter than the equivalent gauge plastic hulls, so they recommend using 11 gauge nitro cards and fiber cushion wads, and 10 gauge over shot cards.

I use home made cards and felt wads in my 12 gauge Euroarms Magnum Cape Gun, cut with a 3/4" punch, which is about 11 gauge. So, I decided to save a few bucks and use these in the brass cases. As it turned out, I would have gotten a better fit with 10 gauge components all around.

Most references I've seen indicate that one should use FFg when loading 12 gauge black powder shotgun shells. However, Goex's load data specifies FFFg (PDF), so that's what I used. (Goex recommends FFg in muzzleloading shotguns.)

Yesterday, I took one box of the Magtech hulls and loaded a few different recipes, as follows:

• 1 oz. #7.5 shot using sawdust in lieu of a fiber cushion wad (a la the Survival Russia video).
  1-1/8 oz. #7.5 shot using a sawdust "wad."
• 1-1/8 oz. #7.5 shot using the same 1/8" thick lubricated felt wad that I use in my 12 gauge muzzleloader.1-1/4 oz. #5 shot with sawdust.
• 1-1/4 oz. #5 shot with felt wad.
• Patched .690 round ball.

All shot loads were primed with Federal No.150 large pistol primers and charged with 80 grains of FFFg Goex black powder, and a home made cardboard over powder wad.

The round balls have two over powder cards, a lubricated felt wad, and a lubricated 0.020" patch, and 90 grains of FFFg.

All shot loads are sealed in place using one of the BPI 10 gauge over shot cards held in place with silicone RTV sealant. I used Gorilla Glue gel super glue for the ball loads because I ran out of RTV.

Some pictures:

The 3/4" oak dowel I used for seating components. I drilled a hole in one end to fit over the primer pocket that protrudes into the case. Yes, the Magtech hulls are balloon head cases. I used my lathe to slightly turn down the dowel so it would go all the way into the case, and to drill the hole.

 Some cases waiting to be primed, a case with the dowel inserted, and a primer sitting on a 1/8" piece of aluminum. To prime the cases, I placed the primer down on the aluminum, centered the case with the dowel in it over the primer, and gave it a few good whacks to press the case down over the primer.

If this makes you cringe, consider that it is exactly how you prime cases in a Lee Loader.

A primed and unprimed case:

 

Make sure the primers are seated flush with the case head. You don't want to accidentally set off a high primer by closing your shotgun.

Next up I poured a powder charge into the case and topped it with a card. For the sawdust shells, I then filled each case to the top with sawdust. I have a No.10 can filled with it that I've been saving to make fire starters.

Then I used the flat end of the dowel to compress the sawdust.

This was topped with another card and then the load of shot poured in.

And here's one of the patched round balls in place:

By using the drilled end of the dowel I was able to keep the sprue centered, facing up.

Finally, it's topped off with an over shot card and glued in place. (This one hasn't been glued yet.)

Advantages of this method include that you don't need any tools you can't find or make at home, and the shells should be reloadable pretty much indefinitely, especially since the case mouths aren't being crimped. Because I'm using black powder, small variations in powder charge aren't dangerous the way they would be with smokeless powder, especially when shooting them through nitro-proofed shotguns.

The main downside compared with loading shotshells with modern components is inferior performance. Modern shotcup wads that protect the shot from deformation in the bore result in better, more even patterns.


Special safety note about the round balls: Before Foster slugs became widely available in the 1930s, "pumpkin balls" were the most common type of single projectile load in shotgun ammo in the US. After the introduction of choke barrels, they were generally loaded with balls significantly under bore size so that if they were fired through a choked barrel, the barrel would not be damaged. They don't compress as easily as Foster slugs. For this reason, I would not fire a patched .690 ball through anything tighter than improved cylinder.

For example, I have an H&R Model 1905 made sometime between 1906 and 1915 with the barrel marked "12 GUAGE CHOKED." I measured the muzzle last night with calipers and it came out at about .695, which is extra-full, or even a turkey choke. I'll shoot the balls through my chopped, cylinder bore H&R Topper.

Hopefully, I'll get to try out these loads in the next few weeks, and will post a follow up.


*Hot glue slug: A field-expedient slug which you cut the crimp off a bird shot load, pour out the shot, then add the shot back after mixing it with hot glue. When the glue hardens you have a slug that's useful at short range. Very similar to wax slugs. Do a lot of research before you make and shoot any, so you don't do anything dangerous.

Reaction to the NRA and NRA-ILA Joint Statement of October 5, 2017

Yesterday, Wayne LaPierre and Chris Cox issued a joint statement, which contained, inter alia:

In Las Vegas, reports indicate that certain devices were used to modify the firearms involved. Despite the fact that the Obama administration approved the sale of bump fire stocks on at least two occasions, the National Rifle Association is calling on the Bureau of Alcohol, Tobacco, Firearms and Explosives (BATFE) to immediately review whether these devices comply with federal law.  The NRA believes that devices designed to allow semi-automatic rifles to function like fully-automatic rifles should be subject to additional regulations.

Link: https://home.nra.org/joint-statement/

We should know by now that when gun banners say, "We want a conversation about gun control," they mean we should shut up while they lecture us. We should also know that when they say we should compromise, they mean for us to give them something while we get nothing in return.

It is not acceptable conduct to this NRA Endowment Life Member for the organization to preemptively surrender any part of our rights by endorsing any new gun regulation. The NRA needs to protect all of our right to bear arms. 

Suggesting that the corrupt and incompetent BATFE get another chance to evaluate the legality of bumpfire stocks is particularly galling. Including a sentence in the press release calling for Congress to pass National Right-to-Carry Reciprocity doesn't balance giving in on one iota of other elements of the RKBA.

NRA, withdraw this statement. Do your damn job.

First Use of the Emtech ZM-2 Antenna Tuner

HF propagation conditions currently suck, but I wanted to try out the Emtech ZM-2 anyway. My first use would be with a random length antenna.

Earlier today I stopped at Harbor Freight and picked up a one pound spool of aluminum welding wire for ten bucks before the 20% off coupon. We've used such welding wire on our camping trips upstate with good results. In fact, my friend who owns the property we camp on built an 80M dipole with it and strung it about 5 feet off the ground, supporting it with fence insulators. Reception on that antenna is excellent and he's made some contacts as well. It's been there over a year and is still usable.

To support my random wire antenna today I used my 31 foot Jackite kite pole with about 50 feet of the welding wire. I also ran a ground line about 25 to 30 feet and held it down with a big screwdriver as a stake.

The wire was so light that the tip of the mast didn't noticeably droop. The antenna was running approximately East-West, and the ground ran out towards the NE.

Aluminum welding wire is light and easy to work with. As seen with my friend's 80M dipole, it'll last long if its not under much strain. It's cheap enough that if you needed to abandon a random wire antenna made from it, that wouldn't cause concern.

My back patio station today was my 2013 MacBook Pro running FLDIGI and WSJT-X, the ZM-2, Yaesu FT-817ND, and Signalink USB digital interface. I also had a CAT cable for rig control.

I followed the instructions in this video to work the tuner. I found it difficult to see the red LED even though it was overcast, so I need to verify that it's in fact working. Maybe it was luck, but by tuning for maximum noise I really didn't have to tweak anything. When I hit transmit, the rig didn't complain about high SWR.

I briefly tried 40M but had issues getting the antenna to tune on that band. It might be the length of the wire, but again I had issues seeing the LED SWR indicator light up.

As I mentioned, HF propagation is really in the crapper. Before setting up out back, I'd done some work inside using my Icom 7200 and the Ultimax 100 end fed on my roof. The random wire seemed more sensitive, based on the number of PSK31 stations that I saw. However, 20M was mostly dead.

After spotting a number of other stations on 20M PSK31 I closed out FLDIGI and fired up WSJT-X to do some WSPR. On 5 watts, I was in fact getting out.

The screenshot is from WSPR Watch running on my iPhone

This table shows the WSPR stations I received in about 10 minutes of listening.

Timestamp Call MHz SNR Drift Grid Pwr Reporter RGrid km az
 2017-09-17 19:28   8P9HA   14.097165   -17   0   GK03fb   0.1   KB3MNK   FN20ic   3378   336 
 2017-09-17 19:28   K7POF   14.097124   -8   0   DM34sr   10   KB3MNK   FN20ic   3312   68 
 2017-09-17 19:28   W6WGF   14.097119   -7   1   EM12rw   5   KB3MNK   FN20ic   2053   61 
 2017-09-17 19:28   VE4WSC   14.097103   -12   3   EN19ku   5   KB3MNK   FN20ic   2019   114 
 2017-09-17 19:26   WA5IWB   14.097094   -14   0   EM10qh   1   KB3MNK   FN20ic   2215   55 
 2017-09-17 19:26   K7RE   14.097146   -10   0   DN84am   1   KB3MNK   FN20ic   2395   92 
 2017-09-17 19:26   K5FRT   14.097012   -21   0   EM10td   0.2   KB3MNK   FN20ic   2206   54 
 2017-09-17 19:24   8P9HA   14.097137   -19   0   GK03fb   0.1   KB3MNK   FN20ic   3378   336 
 2017-09-17 19:24   K6KWI   14.097060   -21   0   DM13cu   20   KB3MNK   FN20ic   3802   67 
 2017-09-17 19:24   N0IJK   14.097052   -19   0   EL19ao   5   KB3MNK   FN20ic   2365   54

I am cautiously optimistic about the Emtech ZM-2 tuner but I need to figure out why I'm not seeing the LED SWR indicator light. My next experiment with it will be with a dipole to be constructed using some 450 Ohm window line that I bought yesterday at Ham Radio Outlet.

Emtech ZM-2 Antenna Tuner

Last Saturday I ordered a pre-built Emtech ZM-2 antenna tuner with UHF connectors and it arrived today.  I wanted something a bit smaller and lighter than my LDG YT-100 for use with my Yaesu FT-817ND. Additionally, I wanted a tuner that would work with either coax cable fed antennas, balanced line antennas, or even just a random length wire with a ground.

Unlike the LDG, the Emtech unit is a manual tuner using a Z-match circuit. However, based on several videos I've watched and reviews I've read, it's quick to tune and gives you a wide choice with antennas and feedlines. (See here for a good discussion of Z-match circuits.)

Weather permitting, I am hoping to try it out this coming weekend. In the interim, here's a good video from W2AEW on how to operate the ZM-2.

NOAA Radio Propagation Dashboard

Currently, HF propagation is terrible, largely due to solar activity. This NOAA Radio Propagation Dashboard helps explain why.

Kel-Tec RDB Field Stripped

This afternoon I took a few minutes, field stripped the Kel-Tec RDB, and took some pictures. The rifle's design is different enough so that I think you'll find them of interest. Clickenzee to embiggenate.

Slightly closer view of the barrel and bolt groups:

Bolt, bolt face, and extractor. Note the dual ejector plungers on the bolt face.

Piston head. It's a little hard to see but there is a weld blob on the top of the piston. Some earlier rifles left the factory without the weld, which leads to malfunctions.

The gas system.

Bottom of the handguard, showing the molded-in M-1913 rail. I have a Rogers Rail Light mounted.

Disassembly to this stage requires you to push out three takedown pins, plus one pin in the bolt carrier group. If you take down the BCG be careful. The firing pin is spring loaded and if you fail to contain it, it will launch itself several feet. (Yeah, it happened to me the first time I stripped the BCG.)

Scoped the RDB

Yesterday I decided to move a scope I already owned over to the Kel-Tec RDB I bought Friday night. My Colt AR15 6721 has been relegated to backup status and was wearing an IOR Valdada 3x25mm CQB scope.

The IOR scope is built with Schott glass from Germany, has very clear optics, and a nice reticle. The 3x magnification works well from close-up to my club's longest range, 200 yards. It's also built like a brick shithouse, so I am not going to worry about BUIS.

Range report to follow as soon as possible.

Picked Up a Kel-Tec RDB Rifle

I did some trading last night at Surplus City and came home with a Kel-Tec RDB 5.56mm bullpup rifle. (I actually went there with the intention of ordering an FN PS90. Maybe next time.)  SC was asking $950. I traded in my CZ-52, Bulgarian Makarov, Ruger SP101, Pietta SAA, and Springfield XD-9, none of which I'd fired in years. He gave me $1000 trade in value, so I also got 500 rounds of CCI .22 Short HV to run through my Remington 550-1.

Kel-Tec gives the OAL as 27.3" with its 17.3" barrel. The weight unloaded is 6.7 lbs. The barrel is 1:7" twist. There's a long, T-marked M-1913 Picatinny rail on top but it comes without any sights. I am debating what kind of optic to mount, but it will probably be something along the lines of a 1-4x variable, not just a red dot.


The RDB is a new design, although the bolt itself is very Stoner-ish and it takes AR15 magazines. It came with one 20-round MagPul P-Mag, an owner's manual, and a sling.

There are numerous sling mounting points for the hook-style attachments. In the pic above I had it mounted as a 2-point sling but I later switched it to a single-point using the swivel located in front of the middle takedown pin.

It's a long-stroke, gas piston design. The gas is adjustable to account for variations in ammo or the amount of crud in the gun. However, reviews I've seen state that very little fouling gets into the action. Empties eject out the bottom, through a port behind the magazine well.

The action is very simple and breaks down with only something to drive out the takedown pins. (They may loosen up over time.)

As a southpaw, the best part to me is that it's totally ambidextrous except for the HK MP5-ish charging handle. It can be reversed without tools. All I had to do was field strip the rifle and then put it in the other way when I reassembled. My initial impression of the rifle is that the ergonomics are outstanding.

Because of the long linkage between the trigger and the rest of the firing mechanism, most bullpups have lackluster trigger pulls. Not so in the case of the RDP. It's actually pretty good with some takeup but it's only around 5 pounds.

Between the adjustable gas system, the lack of fouling in the action, and having the ejection port on the bottom of the rifle so gas gets vented downward, it's supposed to be an awesome suppressor host.

In typical Kel-Tec fashion, they are scarce as hen's teeth, though. Kel-Tec announced it a few years ago but they just started shipping in 2016. They are still really hard to find in shops although there are a bunch on Gunbroker.

MAC posted a nice, in-depth review of a pre-production sample on YouTube in 2015:

I should be able to take it out in the next week or two and will post a follow up after I am able to shoot it.

BBC: Why One Man Left Silicon Valley and Setup a Survival Camp

BBC News published this video, which I think is worth watching. It's only a few minutes long. (I couldn't figure out a way to embed it.) H/T to Tamara on Facebook.

The BBC reporter's reaction to the AR15 was a bit stereotypical, but amusing.

As someone who works in information technology and who is seeing the push to automate more and more, I don't think he's completely off-base.

Heck if I know the solution, though.

Mossberg 500 Super Bantam Shotgun

My 13 year old daughter wants to come hunting with me this year and needed a suitable shotgun. Today, we went to the local Dick's Sporting Goods and picked up this 20 gauge Mossberg 500 Super Bantam for ~$325 + PA's 6% sales tax.

I actually had her try out the Mossberg 510 youth model in .410 bore but she's already outgrown it. That's good because the 20 gauge will throw significantly more shot and 20 gauge slugs are adequate for deer.

Both the stock and forearm are synthetic. The stock is currently setup with a 12" length of pull but it included a spacer to increase it to 13". If she needs a longer LOP it will accept adult-sized stocks. The stock has a good, thick recoil pad on it.

The 22" barrel is threaded for choke tubes. It came with the modified tube in place. Using the included wrench, I swapped that out for improved cylinder. It also comes with a full choke tube. The barrel is topped with a white bead up front and a brass middle bead.

At 5.25 lbs. unloaded it won't be hard for her to carry afield. Heck, that weighs less than her school bag on most days. The stock has a place to attach a sling swivel but the gun didn't come with a stud for the front. So, I found one on eBay and it should hopefully be here by the end of the week. It will thread into an existing hole on the barrel mounting screw. I also ordered an inexpensive sling with swivels and an Outers cleaning kit.

The magazine came plugged so that the only way to load it was singly through the ejection port. The manual states that once your new shooter learns gun safety you can shorten the plug (a dowel) to 9", to allow up to two shells in the magazine. I did so, since my kid is not new to shooting. (Frankly, if they aren't safe to handle a manually operated gun with 3 shells in it, they aren't safe to handle a single shot.)

The unplugged magazine capacity is six 2-3/4" shells. I have some Federal 20 gauge #3 buckshot with which I'll pattern it. It would make a nice home defense shotgun.

Aside from hunting, this will be a good shotgun to introduce my daughter to trap and sporting clays.

Of note, Mossberg has a similar gun in their economy-oriented Maverick line. However, spending more money on the 500 was worth it to us because the Maverick uses a right-handed cross-bolt safety instead of the Mossberg's ambidextrous tang safety. I'm a lefty and my kid is left-eye dominant, and hence shoots portside.

I'll post a follow up after we get the chance to shoot it.