Sunday, October 21, 2007

Doan Magnesium Fire Starter Review

Today I practiced making fire, this time using a Doan magnesium fire starter. This is a piece of USGI gear consisting of rectangular bar of magnesium, to which a ferrocerrium rod is glued on one of the long sides. It also has a hole towards one end through which a beaded chain is threaded, and which can be used to secure it to your kit or to keep a striker handy.

The magnesium fire starters are waterproof and don't burn when solid. To use, you scrape the exposed long side of the bar to make a pile of magnesium shavings, which do burn. Once you've got a good pile, which takes some work, you flip the bar over and use a striker to scrape sparks off the ferrocerium rod into the pile. This will then flare up and light your secondary tinder and kindling.

A hacksaw blade snapped in half works fairly well for making the magnesium shavings and for making sparks. However, I used the reamer on my Victorinox Farmer Swiss Army Knife. It's easier to hold and works well.

While the magnesium shavings burn very hot, they don't burn for very long. Thus, it's critical that you make a big enough pile and have enough dry tinder, twigs, and kindling to keep the fire burning once the magnesium shavings burn out in short order.

My secondary tinder was wood shavings sliced off one of the firewood logs I picked up last weekend at Lowe's. The logs were my fuel, as well. They were supposed to be seasoned but still had a fair moisture content, as I discovered once I got the fire going.

I first created a pile of wood shavings then made a small pile of magnesium shavings next to and surrounded by the wood. The magnesium shavings lit after a few strikes from the ferrocerium but I was unable to get a sustained fire going.

Since my daughters were outside with my and wanted to get one with roasting some hot dogs, I switched over to a Bic lighter. However, I wasn't able to get a sustained fire going until I broke out a Coughlin's tinder wad (a wax impregnated cotton ball) and placed it among the coals left over from the burning wood shavings. That and blowing on the fire finally got it going.

Once the fire was going I saw and heard moisture bubbling out the end of the firewood, so it wasn't seasoned enough. It burned with a lot of smoke, too.

I'm not real impressed with the magnesium fire starter. It takes too long and requires too much effort to create a pile of shavings for your stage one tinder. Also, the shavings are so lightweight that the slightest bit of wind blows them around. Finally, the striker rod on the one side of the bar is thin compared to a Swedish Fire Steel, so it throws fewer sparks.

If I was stuck in the wilderness, would I take a Doan magnesium fire starter over a primitive fire starting method, such as a fire drill? You bet. It's easily pocketable, light, and does contain both a spark source and tinder in one waterproof package. However, I think there are better alternatives. For example, a ferrocerium rod (e.g., Swedish Fire Steel) and a 35mm film canister filled with cotton balls soaked in petroleum jelly take up little additional room but work much better. The PJ cotton balls burn hot AND long enough to get your secondary tinder going. Of course, one could carry the Doan fire starter and the PJ cotton balls, using the Doan's ferrocerium rod to ignite them.

I was also reminded of the utility of a large knife, machete, or axe when making woods shavings or splitting kindling from large pieces of wood. Today I relied on my Mora Swedish Army Knife, (#760MG) which is a great small fixed blade. They are inexpensive, take and retain a sharp edge, and have comfortable handles. However, they are short and light which means it takes significantly more effort to make a pile of wood shavings or split logs. If I'd been able to split more kindling the fire would have gotten going a lot more easily. This could be critical in a survival situation where you need a fire RFN, such as if you need to dry off in cold weather.

Once again, I'm glad I tried this out in my back yard, instead of out in the woods in a serious situation.

Saturday, October 20, 2007

Some Vehicle Preps

Last weekend I picked up a Contico SUV Utility Box at Lowe's to organize the stuff I keep in the back of my Expedition. It' sturdy and just the right size for my truck.

Today I added a few items which may come in handy during an emergency:

  1. My Ontario 12" Camper Machete. It's a nice chopper yet not too large.
  2. One of the Swiss surplus ponchos I picked up a couple months ago from Cheaper Than Dirt. I already had a poncho but this is heavier and can do double duty as a tarp or groundcloth.
  3. Two 3600 calorie packs of Mainstay ration bars.
  4. A coffee can containing a box of REI stormproof matches, a Swedish Fire Steel, 35mm film canister with petrolatum soaked cotton balls for tinder, a space blanket, some paracord, some flat packed duct tape, and a whistle with a compass and thermometer. I sealed the can with duct tape and wrote the contents on the outside with a Sharpie.

The coffee can itself serves a couple different uses. First, it protects the contents. Second, it can be used as a pot.

All of the above augments the stuff in the get home bag kept in the truck.

As we get closer to winter, it's a good idea to reevalute the emergency supplies we keep in our vehicles, and restock or augment them as needed.

Saturday, October 13, 2007

Mainstay Ration Bars

I've been carrying some Mainstay Ration Bars ("lifeboat rations") in the get home bag I keep in my truck. I chose them instead of MREs because they are designed for long term storage in harsh environments. I've had them for a couple years and although still good, I wanted to replace them with fresher ones. So, earlier this month I got some more. Today I decided to try one.

Not bad at all. It has the consistency of a cookie and a lemony taste. I had some water along with the bar and didn't notice that it made me thirsty or if it had an aftertaste.

Assuming your not allergic to any of the ingredients, or don't have any special dietary restrictions, these are worth looking at for emergency rations.

Valiant Large Survival Golok

After reading several online reviews (e.g., on http://www.oldjimbo.com) I got a Valiant Trading Co. Large Survival Golok earlier this week:



This golok is the closest thing I've held to a +10 vorpal sword.

Workmanship is very nice. It's nicely balanced and the buffalo horn handle is comfortable. The blade is ~15.5", hand forged, with a full convex grind and distal taper (thins towards the point). Weight is about 1.2 lbs. It came sharp enough to cut limply hanging newspaper. I almost sliced off my finger tip when wiping off the preservative oil it came in!

They're made in Java, then imported into Australia, then shipped to the US. I bought it from their US dealer, but just read on THR that he's closing up shop. Sad Cost was $89 after shipping.

I took it out back today and used it for pruning some arborvitae. It works really well on woody plants, much better than a machete. The blade cross section prevents it from getting stuck the way a machete can. The handle was comfortable in use. The edge stayed sharp and didn't show any damage even after using the golok in lieu of a hatchet to chop down a couple trunks. I can see this golok being very useful in the woods.

A view in its wood and horn sheath:




Handle and sheath closeup:




Chopping into a branch. You can see how deeply the golok bites:




My reward after a morning of yardwork:

Saturday, October 06, 2007

Chopper Comparison

This morning I was able to do a little comparison between three chopping tools I have in my arsenal: a Cold Steel Trail Hawk, an Ontario 12" machete, and a Harbor Freight 18 machete. The victims of my cutting tests were a few arbovitae trees in my yard which were in dire need of pruning. First, some background on each of the tools.




I've had the HF machete for a couple of years. Like most machetes it's on the soft side and came as dull as a butter knife. I put a semi-usable edge on it with a belt sander last year but was never really happy with it. A few weeks ago I bought some new files, reshaped the edge, then convexed it using sandpaper on top of a mousepad, taped to my workbench. I also drilled the handle for the lanyard and added a paracord wrap to the grip, which greatly improves the feel. The HF machete came with a cheap flimsy canvas sheath. I improved this by covering it with duct tape, first a couple layers of regular duct tape then a final layer of camo tape as shown below. This actually came out pretty good and I will look at giving it a polyurethane clear coat to make it more weather resistant.

I picked up the CS Trail Hawk a couple weeks ago mainly on a lark. I wanted a hawk that was smaller than my Dixon's hawk, which is about the same size as a CS Rifleman's Hawk. The Trail Hawk's head is rather small with a 2" edge, and a hammer poll. It came reasonably sharp, though I touchd it up with some sandpaper and began to convex the edge. The Trail Hawk did not come with a sheath.

The Ontario 12" machete was ordered around the same time as the Trail Hawk. It's made of 1095 carbon steel about 1/8" thick, which is thicker than the HF machete. The plastic handle is molded in place with a D-shaped hand guard. I find it pretty comfortable and like the hand guard. Like the HF machete, it came as dull as a spatula with a very uneven edge. Unlike the unfinished HF machete, it is parkerized. The Ontario has a secondary bevel next to the edge, while the HF does not. As you can see in the picture, I removed most of the parkerizing from the secondary bevel, to reduce drag when cutting. I sharpened the Ontario using files and sandpaper. It's sharp, but not as sharp as the HF machete. The sheath shown with it had to be ordered separately; all it came with was a cardboard blade cover.

With that out of the way, onto the results.

I started out with the Trail Hawk. It penetrated well into an arborvitae but because of the short edge, took a fair amount of effort to cut through the ~5" diameter trunk.

I switched to the Ontario machete next. It penetrated well in the wood and cut a wider swath than the Trail Hawk. It didn't take long to chop down another arborvitae. The longer blade also made it better than the Trail Hawk for limbing the downed trunks. I was quite impressed with how well it chopped.

My use of the HF machete today was minimal. It's better at cutting thin vegetation than the Ontario because (a) it's sharper, (b) it's thinner, and (c) the longer blade achieves higher tip velocity. I used it last weekend on some weeds and forsythia, which it went through like a razor. It also handled some arborvitae well. It has a reach advantage over the Ontario 12" machete, of course.

Naturally, which one of these three choppers is "best" depends on the use. The CS Trail Hawk is handicapped by the short cutting edge. It would probably make a pretty decent thrower, though.

The Harbor Freight machete is great on light brush and even does well on softwoods. With the 18" blade it has a good reach.

The Ontario 12" machete impressed me today with it's chopping ability on softwoods. It's a bit harder than the HF machete so would probably handle batoning a bit better if you hit a bad knot. The length is handy and the handle is comfortable. IMO it would make a very handy tool out in the Pennsylvania woods.

Tuesday, October 02, 2007

A Pair of Victorinox Pioneers

My Victorinox Pioneer that I bought in the early 80s has been my favorite EDC pocketknife of late. It's a good size for pocket carry, has a very useful assortment of tools, is nearly indestructible with its alox scales, and is sheeple friendly. I've been on a bit of a knife kick lately, so when I found out that Amazon was carrying the Vic Pioneer Farmer model in red, I had to get one. (Most of the Victorinox SAKs with alox scales are now silver colored. IMHO, SAKs should be red.) The Farmer adds one implement to the Pioneer, a wood saw. I think this could come in very useful.

Here's a side view of the Farmer next to my old Pioneer, showing the saw:



Note the Swiss shield on the Farmer, compared with the plain cross on the older knife. On the other side of the Farmer there's a rectangular area suitable for engraving. The older knife doesn't have this.

Below is a top view, showing how the Farmer is just a little thicker than the Pioneer. It's still very pocketable, the difference isn't noticeable.



The Farmer's knife blade came with a good sharp edge. The polish on the blades is up to Victorinox's usual high standard, and better than on the older knife, even taking into account the wear and tear it has.

You're probably wondering what the silver cylinders attached to each of the knives are. They're "Peanut Lighters" I bought from Countycomm.com. They are refillable, using standard fluid and flints. With the O-rings, they don't leak or let the fluid evaporate. They aren't windproof like Zippos but aside from that work great. For $5 a pop you can't go wrong with them.

I think I'm going to give my old Pioneer a break as my EDC, and start putting the Farmer in my pocket when I get dressed.

Monday, October 01, 2007

A Couple New Choppers

Last week I received the two new choppers I'd ordered: a Cold Steel Trail Hawk and an Ontario 12" machete.

The Trail Hawk is much smaller than my Dixon's tomahawk. The blade edge is only 2" long. The handle is a full 19". The blade came reasonably sharp but I did touch it up some.

Yesterday I took the Trail Hawk out back and hacked at a couple of things. Due to the light weight it doesn't chop nearly as well as the Dixon's Hawk. I think it would make a decent defensive weapon but it's not as useful a tool as the larger 'hawk.

In contrast to the Trail Hawk, the Ontario machete came as dull as a butter knife. In a few places the edge grind didn't even meet -- the edge was actually flat. The parkerized finish on the blade was even and looks good, however.

Sharpening the machete took a good bit of effort and I'm still not satisfied with it. I started with a couple of files then progressed to 150 grit sandpaper. The sandpaper I had wasn't intended for use on metal so I didn't make much progress before it was shot. Yesterday I ran out and bought some emery cloth and 150, 400, and 600 grit wet/dry sandpaper suitable for use on metal.

I also bought a lawn implement sharpening attachment for my Dremel. I need to improve my technique because I wound up with a really ugly edge after using it on the machete. (I think I'll practice on a shovel before using it on a knife again.) So, I went back to the file and abrasives. After awhile I got a usable edge but it's still not as sharp as I want it to be.

Anyway, once the machete was moderately sharp I took it out back to try. The handle seems comfortable and I like that it has a handguard on it. The balance is different from my Harbor Freight machete (which is thinner but longer) and so it feels quite a bit different when swung. I tried it on a few branches and weeds and it worked OK, but not as well as the HF, which is sharper. The longer HF machete also has the advantage when it comes to reach. For the kind of use I've been putting it to in my yard, this is significant.

I did use the Ontario to split a couple of logs using a baton. It worked pretty well. The machete is robust enough that you can feel comfortable wailing on it with a baton without fear of damaging it.

I got the Ontario from Knifecenter.com. They were out of sheathes so I've ordered one from Smokey Mountain Knife Works along with a couple of other items.

Saturday, September 22, 2007

Dixon's Tomahawk

I bought a tomahawk at Dixon's Muzzleloading Shop in Kempton, PA about 10 years ago. For the past few years I've used it as a garden tool. The relatively thin blade chops through the wood on my property well.

The edge had gotten dinged up pretty badly from hitting pebbles. Today I went out and bought a couple of new files to resharpen it. The blade is fairly soft, so with the sharp new files it didn't take me long to get the edge repaired. I then taped a sheet of 150 grit sandpaper on top of a mousepad to my workbench, and polished it up. I wound up with a nice convex edge. The 'hawk will now slice newspaper.

While I was working on the 'hawk I decided to wrap the handle with paracord. I left a gap of exposed wood as a grasping surface, because I thought it might be too thick if I wrapped the whole thing. At the bottom I drilled a hole through the handle and made a wrist loop.

I took her out back and whacked a few things. Big improvement. Here are a couple of pictures.





I have an Ontario 12" machete and a Cold Steel Trail Hawk on order. It'll be interesting to see how they compare as choppers.

Edited to add:
It weighs 1 lb. 7 oz. Total length is 18-3/8", and the edge is 4".

Thursday, September 20, 2007

Thoughts About Survival Knives

I have been reevaluating my choices for survival knives lately.

Previously, I've favored smaller blades. When I was in a Civil Air Patrol ground search and rescue unit I happily got by with first a 5" USAF Survival Knife, then later a Schrade Uncle Henry LB7 Bearpaw folding hunter.

However, during the course of some recent firestarting practice I came to appreciate the chopping power of my Becker BK7. It's size made splitting branches easy when used with a baton, plus with its size I was able to chop at branches to chip off wood shavings for fire starting.

If I was absolutely restricted to one knife and one knife only in a survival situation in most of North America, I'd choose the BK7 without second thought. With a 7" blade, it's a good compromise between a small knife and a big chopper. But since this is a preparedness site and we believe in thinking ahead, IMO it's better to include a minimum of two knives in an emergency kit in my environment (Pennsylvania). Specifically, a small to medium sized blade teamed with a larger knife or hatchet. These will complement my everyday carry Victorinox Pioneer Swiss Army Knife.

The problem with relying exclusively on a small blade is that you may need chopping power in an emergency. Something that can cut the limbs off trees to make shelter or obtain firewood, can split kindling for a fire, or cut the legs off a downed deer. You might be able to perform these tasks with a 4" knife but not as easily as with a larger blade. As an alternative to a large knife, one might carry a hatchet or tomahawk for these chopping duties.

Conversely, a large knife is awkward to work with when performing fine cutting tasks, e.g., whittling camp implements from sticks. And like it or not, large knives tend to alarm urbanites and suburbanites who you may need to deal with.

The smallest blade, the SAK in my case, handles fine cutting tasks, doing so much more conveniently than a larger knife. It's small enough to carry in pocket virtually everywhere yet large enough to handle most cutting tasks I run into on a daily basis in an urban environment. The Pioneer has a spear point knife blade, an awl/reamer, a can opener with small screwdriver on the tip, a bottle opener with a larger screwdriver tip and a wire stripping notch. Victorinox makes another variant of the Pioneer, the Farmer, which adds a saw blade that could be useful. One reason I'm partial to the Victorinox Pioneers is that the handle scales are made from aluminum, so the knives are very rugged.

An alternative to a SAK is a multitool of the Leatherman, Gerber Multiplier, or Victorinox Swisstool type. These add a variety of tools to the basic knife blade, including pliers. I prefer the Victorinox multitools as IMHO they are higher in quality than the Leathermans or Gerbers. Multitools are heavier than pocketknives, so they may or may not work for you.

The medium blade handles larger tasks like skinning game or making fuzz sticks for fire starting. This can be a short fixed blade such as a Mora or a robust folder, such as my aforementioned Bearpaw or a Buck 110. For safety's sake, a locking blade is best if you choose a folder, although I've never managed to hurt myself due to the lack of a blade lock in about 30 years of carrying folding knives.

A side note about folders: The ability to open a folding knife with one hand is important, in case you only have one usable hand due to the other hand being either occupied or injured. Folding hunters such as the LB7 have sufficient weight in the handle to allow the blades to be flicked open. You grasp the blade then flick the handle downwards. The downside to this is that it's not as safe as a knife designed to be opened with one hand, such as a Spyderco Endura.

If you prefer a fixed blade over a folder for your medium sized knife, then a Mora makes a great choice. Although inexpensive, they are good quality knives and take a keen edge without being too hard to sharpen.

For a large chopper I have on order an Ontario 12" machete with a knuckle guard. The foot-long blade should work better than the BK7's 7" blade to clear a campsite, split kindling when used with a baton, and would make a formidable defensive weapon should the need arise. If I lived further south I'd go for a full size 18" machete.

Given my druthers I prefer knives made from carbon steel, especially for large knives. Carbon steel knives tend to be (a) easier to sharpen than stainless, and (b) tend to be a bit more rugged. The Ontario is made from 1095 carbon steel, though my Bearpaw's blade is made from stainless. An exception is the stainless used by Victorinox for their Swiss Army Knives. It's on the soft side and doesn't take me long to put on a razor edge using an Arkansas stone. I touched up the edge the other day and it's freaking sharp!

An additional consideration is blade thickness. This isn't as much of a consideration in folders, but some fixed knives come with blades that are thick enough in relation to their width, that the grind angle is such that they're hard to sharpen. The USAF Survival Knife is a good example of a knife with a blade too thick for its width, unless it was hollow ground.

Knives are among the most important items in your survival kit. They should be selected with care to maximize their utility in your environment. Between the SAK, LB7, and machete, I should be able to handle anything that needs cutting in an emergency.

Monday, September 17, 2007

Personal Financial Management

Part of being prepared is keeping your financial house in order. I came across this article, which I feel is worth reading.

Thursday, September 13, 2007

Gerber Firecracker Flashlight

Last weekend while up at REI, I picked up a Gerber Firecracker flashlight. Made of machined aluminum, it has 1 white LED, uses 1 AA battery, and puts out 18 Lumens. If you twist the tailcap it'll operate in continuous mode, and can also be used as a momentary switch if you push it in.

According to Gerber the beam will reach 160 feet. It'll reach the back of my yard from inside my house, through a sliding glass door that needs to be cleaned. It's not as bright as my Surefire G2 but it's more useful as a utility light, as opposed to a tactical light like the Surefire.

The one thing which could be improved would be to make the lanyard hole larger. It's only a couple millimeters in diameter, so in order to attach a paracord lanyard I first put a small loop of mason's twine through the it, then ran the paracord through that. (I want to find a small split ring to replace the mason's twine.)

Overall I'm quite pleased with the light. It's taken up residence in my laptop bag, replacing an older, larger light.

Tuesday, September 11, 2007

Fire Starting in the Dark and Wet

In my Sunday post I described how I did some backyard experimenting with fire starting. Since my goal was to see if a Ballistol-soaked cleaning patch would catch the sparks from a fire steel and act as tinder, the nice weather on Sunday was a bonus.

However, when you're out in the woods, whether by design or bad fortune, odds are that weather conditions won't always cooperate. Your fuel sources may be wet and it may be actually raining. Just as bad, it may be dark. (For some perverse reason, it seemed that every time my CAP squadron went on an FTX, we didn't pitch camp until it was dark and raining.)

So, tonight I went out back again for more practice. It rained last night and earlier today, so everything was wet. Before heading outside I gathered several items:

1. A Swiss surplus rain poncho, mainly for use as a mat to sit on. I also used it to collect wood shavings.
2. My Becker Combat/Utility 7 knife, along with matches and tinder in a small Altoids tin in the sheath pouch.
3. A Rayovac LED headlamp.
4. My Victorinox Pioneer Swiss Army Knife, to which is attached a County Comm Peanut Lighter. If I step out of the house, this combo is in my pocket.
5. 1L Nalgene bottle of water to douse the fire when I was finished.

I wanted to see if I could get a fire going using just a match and tinder gathered from my yard. I gathered some small dead branches from a tree in my yard. These felt pretty dry. I broken them up and set them aside.

I took a small branch which didn't seem soaked from my wood pile, peeled off the bark, and made a pile of shavings from the dry wood within.

Rather than placing my pile of shavings directly on damp ground, I first made a platform of dry sticks. Doing so keeps your tinder from getting damp.

The first hitch I ran into was that I could not get my strike anywhere matches to light, even using a dry rock as the striker. I don't have a striker from a match box in the fire starting kit in the Becker Sheath, something I must remedy.

I decided to light the match with the Peanut Lighter then try to light the pile of shavings. What I discovered was that whatever wood this was would ignite, flame, then cool down to a coal and then go out before getting any real flame going. Discouraging to say the least.

In exasperation, I took half of a petroleum jelly cotton ball out of the fire starting kit and placed it in the middle of the pile of shavings, then lit it with the Peanut Lighter. The cotton ball with PJ burned hot and long enough to ignite the wood shavings and sticks that I added. Shortly thereafter I had a small blaze going.

After dousing the fire and coming inside I took another match and tried to light it using the grout in my slate floor in my office. This has worked in the past, but tonight, no dice. I got one spark but the tip of the match wore away before igniting. I put the match in the flame of a lighter and it did ignite, so it may be that it's too humid for the strike anywhere matches to light without a matchbox striker or external help. Not something I'd want to discover in an emergency.

Lessons learned:

1. Lighting a fire when stuff is wet takes a lot of work.
2. Carry good tinder with you. Don't depend on being able to find natural tinder when you need it. Cotton balls soaked in petroleum jelly can be made at home, are cheap, and work wonderfully.
3. As a corrollary to #2, if you do find good tinder while roaming the woods, gather some for later use.
4. Even if your matches are strike anywheres, carry the striker from a matchbox with you.
5. Have at least one backup means of making fire. E.g., a lighter. I wholeheartedly recommend the Peanut Lighters from Countycomm.com. They are inexpensive, small, carry easily in a pocket, and don't leak. Mine has not been refilled in at least two weeks. I also like ferrocerrium rods which can be struck to generate a shower of hot sparks. They last a long time and work when wet.
6. A large knife will make it easier for you to make fire. It's much easier to make wood shavings with a good sized belt knife than with a pocket knife. You can also use a large knife to split open wet branches to get at the dry wood within.
7. Aside from keeping you dry, a poncho can be used to collect wood shavings you make and keep them off damp ground.
8. LED headlamps rock. It would have been a lot harder to work in the dark if I had to hold a flashlight in one hand.
9. Setting things on fire is fun.

Sunday, September 09, 2007

Practiced some fire starting today

Fire making is a skill that you need to learn and then practice. Although I've started plenty of camp fires, every so often I like to try something a little different to see if it's something I can use. For example, my Marlin 336 has an Eagle Industries Stock Pack on the butt, inside of which I carry a small cleaning kit, a 35mm film canister filled with cotton balls soaked in petroleum jelly for use as tinder, and a Swedish Fire Steel. The latter is a ferrocerium rod and steel striker, which can be used to throw a shower of sparks. Someone recently suggested that the Ballistol in my cleaning kit might work as a fire starter, something I wanted to try out.

Here's what I gathered in my backyard to do a little experimenting:



On the left are some large sticks to use as fuel. Then my Becker Combat/Utility 7 knife, tomahawk, Ziploc containing the cleaning kit, tinder and fire steel, then some small sticks for use as kindling. I wound up not needing the tomahawk. The Becker worked well to shave down a bunch of fuzz from the large sticks, and to split them so the inner dry wood was exposed.

Here's the pile of wood shavings ready to go. The white thing in the middle is a cleaning patch wet with Ballistol.




My hope was to use sparks from the fire steel to ignite the Ballistol-soaked patch, which in turn would ignite the shavings. No dice. It simply would not light. This demonstrates that while something might seem like a good idea in theory, it won't necessarily work in practice, and one should have a backup plan.

My backup plan is the fire starting kit kept in the pouch on the Becker's sheath. It's a small Altoids tin with some strike anywhere matches, and some PJ-soaked cotton balls. The wood shavings were thin and dry enough so that I didn't need to use a cotton ball. One match was all it took to get the shavings burning nicely. I then added sticks about as big around as a pencil, and once they were burning I added thicker wood. Here's my fire after it was burning for a little while:



As you can see, I filled the Spaghettios can with water to see how long it would take to boil. Only a few minutes, as it turns out.

While I was experimenting out back, my four and a half year old daughter Alexandra came out, so I was able to teach her about camp fires. We even put the fire out with water, then rebuilt it using one of the PJ-soaked cotton balls as tinder.

It was a fun way to spend a couple of hours.

Monday, September 03, 2007

Deal on Wenger Swiss Gear Water Bottles

I came across a great deal today at BJ's Wholesale Club. They had a four-pack of Wenger Swiss Gear 32 oz (1L) Lexan bottles for $7.90 before tax. These are very similar to the Nalgene 32 oz. wide mouth bottles that normally go for about $10 each.

The Wenger bottles are about the same diameter as the Nalgenes. The Olicamp Space Saver cups which I got from Campmor fit over the end of a Nalgene will accept a Wenger bottle. However, the mouth on the Wenger is a little larger than the Nalgenes, so replacement caps or water filters designed to fit the latter won't work on the Wengers. For less than 25% the cost of a Nalgene, I can live with this.

Saturday, August 25, 2007

Labor Day Sale at REI

REI is a great source of preparedness gear. They are now running their Labor Day sale and has some really good deals. I just got back from the store and picked up two Freeplay Sherpa crank-rechargeable flashlights for about $19 each. Full list on these is about $36 each. You can also charge them via a wall wart. One will go in each of our vehicles.

The other good deal I got was a grey REI Lode waist pack for $15 (normally $20). I figure it'll be handy when traveling, and I think it'll work pretty well for CCW of a J-Frame or K-Frame in a holster.

If you don't have an REI locally check out their website at www.rei.com.

Thursday, August 23, 2007

Marlin 336 .30-30

Last Fall I picked up a 1978-vintage Marlin 336 in .30-30. I bought it primarily for deer hunting, but it would make a formidable defensive rifle. I finally got around to taking some photos. Click on the thumbnails for larger pictures.



It's fitted with a Williams FP336 rear sight and Firesight red front bead. To allow more light onto the front sight I drilled a hole in the top of the front sight hood (not shown).


I finally got around to taking pictures of my 336 tonight. My rifle is a .30-30 made in 1978, before Marlin added the crossbolt safety. I bought it last Fall at a gun show in Valley Forge, for both hunting and SHTF.

It's fitted with a Williams FP336 rear sight and Firesight red front bead. To allow more light onto the front sight I drilled a hole in the top of the front sight hood (not shown). The sling is a British surplus L1A1 sling, which is basically a nylon version of the Lee-Enfield sling. Light, rugged, simple. It's attached using a set of Uncle Mike's QD swivels. I really wanted a butt cuff to carry extra ammo on the rifle. However, most cuffs don't work for lefties, the one I did find was $80. Instead, I picked up an Eagle Industries stock pack. Aside from 5 cartridge loops it has a zippered pouch which I put to good use.



Inside a Ziploc bag inside the stock pack, I keep the following items to help me maintin the gun in the field and to start a fire, in case I get stuck out overnight:

  • Swedish fire steel
  • 35mm film container stuffed with petroleum jelly-saturated cotton balls, for use as tinder.
  • Some .270 - .35 caliber cleaning patches
  • A couple of pipe cleaners
  • A pull-through made from the orange pair stripped from a piece of CAT5e cabling
  • A bottle of Ballistol (originally a RemOil bottle)
Lever action rifles may not get the same press as bolt actions or tactical semiautos, but remain very effective hunting and defensive arms. The Marlin holds 6 rounds in the magazine and can be topped off without opening the action.

The .30-30 is well suited for hunting medium and big game. Ammo is relatively cheap, easy to reload for, and it's available pretty much everywhere in the US. It's very easy to scrounge once fired brass around the deer season, as long as you're not in a shotgun-only state. The round itself is quite accurate. Recoil in the Marlins isn't bad (I find Winchester 94 carbines to kick too much for my comfort, however). Hornady's new LEVERevolution® ammo extends the effective range of the round beyond 200 yards.

In my humble opinion, a .30-30 lever action, whether a Marlin or Winchester, is a very useful addition to one's survival battery.

Wednesday, July 18, 2007

Emergency Ration Taste Test

The August 2007 cover story in Popular Mechanics is about disaster preparedness. Meanwhile, PM has posted a comparison of three different emergency ration bars on their website, here.

{H/T InstaPundit.}

Saturday, July 07, 2007

IOR Valdada 3x25mm CQB Scope Review

I formerly had a Hakko 4x21 scope mounted on my Colt AR-15A3 Tactical Carbine. I was considering replacing it with a Trijicon ACOG, in order to get a truly SHTF-worthy piece of glass. After doing a lot of online research and some comparison shopping, I got an IOR Valdada 3x25MM CQB scope instead.

I chose the IOR scope over the ACOG for two primary reasons: (1) cost and (2) the IOR's longer eye relief, which makes eye position much less critical.

IOR Valdada is a Romanian company which has been making scopes and binoculars since the 1930s. They use German-made Schott glass. The lenses are multi-coated to reduce glare, and the scope itself is sealed and filled with nitrogen. This should prevent any interior fogging. The optics are very clear with good resolution.

The IOR scope is compact but weighs in at one pound. It feels very solid. The adjustment clicks for windage and elevation are well-defined. The glass is very clear, definitely better than the Hakko's. The IOR CQB reticle is interesting and incorporates ranging features. The center dot subtends 2 minutes of angle (MOA, or about 2" at 100 yards), so it'll be more precise than the ~4 MOA dot in the Hakko.

The scope's reticle is etched on glass and can be illuminated using a battery powered built-in light, which uses CR2032 lithium coin cells. Without illum, the reticle is black. When illuminated, it's red, except for the horseshoe-shaped thingy in the reticle, which remains black. The illumination is not bright enough to be useful in full daylight. Even at its highest setting, the reticle just barely turns red. The illum works well at dusk and after, however.

The scope has a removable Picatinny rail sleeve around the objective lens side, intended for mounting tacticool stuff like a red dot sight, laser, or light. I have no plans to use the rails, but intend to leave the sleeve on as protection for the main body of the scope. The scope itself mounts to a Picatinny rail using a built-in mount secured by two captive nuts. This is not a quick-release design. The scope feels very rugged, but in the hopefully unlikely event that it goes TU, I'll need pliers or a wrench to remove it so I can use a back up iron sight (which I need to acquire).

After receiving the IOR scope, I bore sighted it at about 25 - 30 yards using a laser boresighter. (A toy house in my backyard stood in for a target.) Yesterday I got it out to the range and zeroed it on an SR-1 target at 100 yards. The laser bore sight got me on the paper but about 6" high and 6" left. It was short work to get POA to equal POI.

Adjustment of the scope is a bit different than most American hunting scopes. The windage and elevation knobs have hand adjustable turrets. Elevation goes from "0" up, while windage has a "0" with adjustments in both direction. If you reach the limits of adjustment, you loosen two Allen screws on the turret knobs and turn the turret independently of the outer ring that has the markings on it. Once you're zeroed, place the outer rings at the zero position and then retighten the Allen screws. An Allen key is provided with the scope for this purpose. The elevation wheel on my Hakko worked similarly.

IMO, the following areas could be improved:

1. Make the illumination brighter so it's useful in daylight.
2. Illuminate the horsesho part of the reticle, so that it can be used as a quick, coarse aiming point at "oh dammit" distances.
3. Replace the mounting nuts with thumb nuts similar to those seen on removable AR-15 carry handles. Or make a quick-release mount.
4. Improve the operator's manual. It's a couple of sheets that look like they came out of in inkjet printer. A better explanation of the scope's range finding reticle would be helpful.

Overall, I am pleased with my choice. The IOR Valdada 3x35mm CQB scope is rugged, has clear optics, a good reticle, and its compact size matches my carbine well.


Technical specs for the IOR Valdada 3x25mm CQB Scope:

Magnification 3x
Objective diameter 25mm
Field of view at 100 yards 31 feet
Exit pupil diameter 8.25mm
Eye relief 3.50 inches
Diopter adjustment -4 to +4 dpt.
Click adjustment 1/4 min.
Tube diameter 30mm
Length 5.65 inches
Weight 16 oz

Sunday, July 01, 2007

REI is selling Mountain House freeze dried food at 20% off in conjunction with their Fourth of July sale. I haven't had any freeze dried food in many years and wanted to try it out as potential food for my emergency stash. I live about 5 minutes from the Conshohocken, PA REI, so today I went over and bought three of their single-serving Pro-Pak meals. The Pro-Paks are vacuum-packed so that they don't take up too much room in a pack. Between the freeze drying and vacuum packing, they should last years.

I bought one each of the beef stroganoff, spaghetti with meat sauce, and scrambled eggs with ham and green and red peppers. I tried the beef stroganoff for lunch. To prepare it, you add 1.5 cups of boiling water to the Pro-Pak pouch, stir well, seal it, let sit for for about 8 - 9 minutes. You can then open it up, stir again, and eat it right from the pouch.

It was quite good. Surprisingly good for food that just got reconstituted. I am impressed. The 16 oz. size was perfect for me, enough to be filling but I'm not overstuffed. This particular meal has a total of 520 calories, 190 of which are from fat. It also has 1920mg of sodium, so people on special diets need to take note.

I see a few advantages of freeze dried meals:

1. LONG shelf life. I've seen some advertised with a 30 year shelf life. The beef stroganoff's pouch is stamped "best used by December 2013." AFAIK it'll be safe beyond that but the taste may deteriorate.
2. Lighter in weight than food which hasn't been dehydrated, e.g., cans or MREs.
3. Easy to prepare. Just add boiling water to the pouch, and wait about 10 minutes.
4. The pouch that it's packed in can be used to reconstitute and serve the food, then discarded. No need to wash dishes.

There are some cons:

1. High sodium content.
2. You have to provide water to reconstitute them.
3. Said water needs to be hot, preferably boiling, for the food to reconstitute in a reasonable amount of time. This means you need something to boil the water in, and something to heat it.

I am planning to pick up some more while it's still on sale.

Wednesday, June 20, 2007

Physical Fitness for Preparedness

One of the more important things for emergency preparedness is physical fitness. By this I don't mean you need to be able to run a 10K or bench press 200 pounds. However, you should be in decent enough shape so that if necessary you can walk at least 5 miles, or perform damage control to your home after a storm.

This is an area in which my preps have been lagging.

The men on my father's side of the family tend to develop guts, and I inherited the trait. In fact, it's been a bit of a joke topic among my friends. Compounding my natural tendency to put on weight around my gut was a bout of poison ivy I had last year, for which I had to take steroids to reduce the inflamation to barely tolerable levels. A side effect of the steroids was that I put on about 13 pounds of pure flab in the space of two weeks, and it never went away.

This week I decided to do something about it. On Monday I walked two laps around my neighborhood (each lap is a mile). I missed last night due to having to stay home with my kids and then a thunderstorm, but I got out and did another two miles tonight. Brisk walking is a good low impact exercise that gets your heart rate up. My wife started it a month or so ago and has already lost about 10 pounds, doing one lap each day.

As for dieting, every single person I've seen who diets has eventually regained any weight lost, and then some. So, I don't plan to diet, but I will try to cut out drinking any soda. I'm hoping that if I can keep this up that by the end of the summer I'll at least lose the 13 extra pounds I packed on last year.

Wednesday, June 06, 2007

DIY Portable Power Pack

I found this article today on eHam.net: Time For a New Portable Power Pack? It's a rather nifty homebrewed portable battery system for powering radios and other electronics.

Saturday, June 02, 2007

Swisstool Follow Up

I took the Swisstool RS out back and tested out the knife and saw blades. Both cut well. I managed to slice some skin off the tip of my right index finger while cleaning the knife blade and didn't notice it until I saw something funny on the blade. It's sharp!

I posted my review to a few places aside from this blog and got some good feedback. Over on Arfcom's Survival Forum, "nightfighter4d" posted from Iraq:

I've been saying once you get a Swiss tool the Gerber / Leatherman debate becomes moot. I love my Swiss Tool. I will once again say that the Swiss Tool is BOMB proof. I know from experience. Many happy years of use.

You forgot two tools Dave
The Pry Bar.
With the pliers out I hve used them to pry open more than one ammo crate.
The hammer.
I have driven nails with it closed up. As long as you use the side of the handle you are fine. A lil hard to control.

Once Again BOMB proof

And on the Yahoogroups Backwoodsman list, Chuck M. noted:

I can concur with everything Dave says here and more. I bought mine almost 5 or 6 years ago and it has been great. I paid under $40 back then, but at 60 or 70, it is still a deal. I actually bought 2, the second one went to a friend just before he traveled to Afghanistan as a contractor. This guy is a retired SEAL. He appreciated the gift somewhat when I gave it to him, but he really fell in love when they hit the ground in A-stan. You see, they had pallets filled with crates of equipment, weapons and ammo and stuff, but no one, anywhere, had a tool to open things up. They were alone on a deserted dirt runway in the middle of nowhere with no weapons, tools, ammo, etc. Then he remembered my gift n his belt and used it to get at their stuff. Boy, did I get a nice "thank you!" the next time we were able to communicate.

It still gets used regularly as he has pretty much been "over there" (Afghanistan and Iraq) constantly for 4 or 5 years now, God bless him...




Friday, June 01, 2007

Victorinox Swisstool RS Multitool

I just got a Victorinox Swisstool RS multitool.

I've had a couple of Gerber Multipliers that have served me well but kept reading how good the Swisstools are, so I ordered one from Amazon last week. My initial impression is, "WOW!" The Swisstool is really well made and finished. It feels considerably more solid than the Gerbers I have, or the Leatherman tools I've handled. I shouldn't be too surprised, since I have four other Victorinox Swiss Army Knives: a Cybertool 41, and three Pioneers, one of which I've gone back to my everyday carry knife, having bought it in the early 1980s. (I keep one Pioneer in each of our vehicles for emergency use.)

The Swisstool RS includes the following tools:

* Pliers
* Screwdriver (2mm)
* Screwdriver (3mm)
* Wire cutter (for wire up to a hardness of 40 hrc)
* Screwdriver (5mm)
* Bottle opener
* Screwdriver (7.5 mm)
* Large blade
* Scissors
* Belt cutter
* Wood saw
* Reamer/punch
* Phillips screwdriver
* Chisel/scraper
* Strong crate opener
* Wire bender
* Wire stripper
* Wire scraper
* Wire crimper
* Can opener
* Ruler (9 inches)
* Ruler (230mm)
* Hard wire cutter

Except for the pliers, the individual tools can be accessed without opening the tool. Each tool locks in place, so you don't have to be concerned with them closing on your fingers. The handle is contoured so that it doesn't dig into your hand when you squeeze down on the pliers. The knife blade, belt cutter, and reamer are very sharp. The seat belt cutter is a serrated, curved blade with a round point. The cutting edge is on the inside of the curve. I could this being useful on boats when you need to cut something but don't want to risk using a pointy knife. The scissors are slightly larger than those on my Cybertool 41, with which I've cut a fair amount of CAT5. The scissors are nice and sharp.

A well-constructed black nylon belt sheath with a snap closure was included. The sheath is designed to stay open so that you can easily re-sheath the multitool with one hand.

So far, I've used the bottle opener, to open a bottle of Yuengling Lager. Works great. :-) I also tested the scissors on some heavy corrugated cardboard and they worked well.

The Swisstool comes with a lifetime guaranty from Victorinox against defects in materials and workmanship.

MSRP is $100 but many places online sell it for much less. I paid about two-thirds of that at Amazon.

If you're in the market for a good multitool, the Swisstools from Victorinox are definitely worth looking at.

Sunday, May 20, 2007

REI Basecamp 6 Tent

A couple weeks ago while REI was running a sale, I bought one of their Basecamp 6 tents for family camping and bug out use. It's a six person dome with aluminum, shock corded poles, and a separate rain fly. (My family is four people but I wanted a bit more space than a 4 person tent.) It's self-supporting but has loops to stake it down if it's windy. The floor is 10'5" x 8'4". This afternoon I finally had a confluence of good weather and free time, so I got to set it up in the backyard.

Here's how it looks without the rain fly:


And here it is with the fly:


Closeup of the vestibule, which'll be handy for gear storage:


In the last two pictures, you can see one of the two vents in the fly. These are held open with Velcro-encased plastic rods, that you access through zippers in the roof of the tent. Unless rain blows into them they should be weather-resistant. They can be closed if you really need to batten down the hatches.

I have several more pictures of the tent here.

Inside, there are several loops and mesh pouches sewn to the tent wall, along with a mesh gear loft up top, for stowing small items. If you don't use the loft there's a sturdy loop sewn to the center of the roof, from which you can hang a lantern. I am very pleased with both the workmanship and design of the tent, and I'm really looking forward to taking it out into the woods this summer.

Saturday, May 12, 2007

Quicksilver Radio PanelRelief(TM)

Hmm, haven't posted here in awhile.

Last night I installed a Quicksilver Radio PanelRelief(TM) bulkhead in my ham shack/office/laundry room (can I multi-task or what?!). The PanelRelief is an adjustable two-piece Lexan panel that sits in a window, and has two M-M connectors. The one I ordered has two SO-239 connectors. This allows me to run my antenna cable into my shack through the window without having it open to the elements.

Along with the PanelRelief, I got a 3-foot antenna patch cable to connect the inside connector to my FT-7800R, a roll of Coaxseal, and a single PowerPole to dual PowerPole splitter cable.

I tested the new setup by getting on last night's MARC net. Everything sounded good to me and apparently my signal was getting out fine.

Around 1700 tonight I heard thunder so I ran into the office and disconnected the patch cord from the PanelRelief. The easy ability to do this was another reason I got it.

Wednesday, March 28, 2007

How to Practice Law in a Barn

New Orleans attorney Jack Deverin wrote an interesting article in December that I just ran across. "How to Practice Law in a Barn" describes how he continued his law practice in the aftermath of Hurricane Katrina. In it, he provides valuable information on business continuity in the the wake of disaster. Check it out.

Friday, March 02, 2007

Henley's Twentieth Century Book of Recipes, Formulas and Processes

I found this book today via Jerry Pournelle's site.

It's the sort of reference you'd want around after a TEOTWAWKI event. Or just to learn how to mix up stuff in the garage sure to piss off the Feds. ;-)

The PDF version is a facsimile of the c.1914 original. It's rather large at over 800 pages and 116 MB but whoever created the PDF also OCRed the file, so it's searchable. If you have a slower connection or an older computer you'll probably be better off with the .txt version, which is only 3.5MB.

I may print it out, two pages to a sheet, and stick it in a binder.

Saturday, February 17, 2007

Post-Storm Lessons Learned

It's been too long since I posted anything here.

This past week we got a major snow and ice storm in Pennsylvania. My area didn't get too much snow, but we did get a few inches of sleet which shortly compacted into an ice crust. Thankfully, I was able to work from home so didn't have to try venturing out into it, even though my employer was open.

When it came time to clear my sidewalks and driveway I ran into trouble. My snowblower had been sitting since last year and both tires were flat, and unseated from the rims. I wasn't able to get them back on myself. (I know about the starting fluid + a match trick, but didn't want to blow myself up.) Luckily, my neighbor bailed me out and cleared off my sidewalk with his snowblower. I could have shoveled it, but this stuff was heavy and the whole reason I bought a snowblower was to save my back.

This morning I took my snowblower out of the shed and took the wheels off, then brought them up to the service station at the end of my block, where the mechanic was able to get the tires seated on the rims and inflated. I wasn't the first person to do so since Wednesday. Now it's all back together with a block of wood underneath the center, keeping the wheels off the ground while it's in storage. Annoying but now I know better.

Hopefully more people will take away some lessons from the I-78 SNAFU which makes my little inconvenience a trifling matter. As you're probably aware, many motorists got stranded on I-78 in Berks County, many of whom had to sit in a 50 mile traffic jam through a blizzard. PennDOT could've done better, but if you're traveling in winter it's foolish to go unprepared for getting stuck, even if you plan to take only major highways. At a minimum, dress appropriately, make sure your car has water and food for at least 24 hours, a candle lantern and matches or a lighter*, blankets or sleeping bags for each person, and a charger for your cell phone. A CB radio is a very handy thing to have when on the highway.



* Aside from light, a candle can warm the interior of a stranded vehicle. Many of the folks stuck ran their cars for heat until they were out of gas.

Saturday, January 13, 2007

DIY Soda Can Lantern

I got this idea from the DIY Vietnam Lantern post in the Arfcom Survival Forum. It cost nothing and the only tool I used was the blade on my Swiss Army knife.

You need two soda cans. Cut away most of one side of the first can. Next, cut the bottom off of a second can about 3/8" above where the wall and the base meet. Put the cut off bottom inside the first can and place a tea light in the center recess.



And a second shot with the lights out:



The silver inside of the soda can maximizes the limited amount of light you get from a candle or tea light and shields it from drafts. Note that the can does get hot so be careful if you pick it up. I wouldn't walk around with this, since if you trip you'll be dropping a lit candle and could start a fire. But for emergency use in a power outage, or placed on the dashboard of a snowbound car, it would be handy. (Make sure you crack a window if you're using it in a car.)

Sunday, January 07, 2007

Will your phone work with the power out?

Will your phone work with the power out?

Old fashioned line-powered phones don't need an external power source. They get their operating power right from the phone line.

However, most of us have cordless phones with a base station and one or more handsets. Many of us use VOIP phones, such as Vonage, which use our Internet connection. No line power there.

The easiest way to ensure you have a working telephone during a power outage, if your phones are not line powered but you still have regular phone service, is to keep a line powered phone around. You can pick them up cheap at Lowe's or Home Despot for around $10 each. If you have VOIP service which depends on an Internet connection*, then you need a battery backup, AKA uninterruptible power supply.

You can buy UPSes meant for computers and networking gear at places like Staples, Office Depot, Microcenter, or CompUSA. Well known, reputable brands include Belkin, American Power Conversion (APC), and Tripplite. Prices will range from a low of around $30 to enough to melt your Master Card.

UPS capacity is measured in Volt Amps (VA). The more the VA, the longer you'll have power available. How long it'll last depends on what you have connected to the UPS. E.g., if you keep surfing the web on battery backup it's going to kill your battery sooner than if you have only your Vonage router and cable modem connected.

Note that some equipment will continue to draw power even if the power switch is off. E.g., most recent PCs have a power switch on the front of the case and a second one on the power supply in back. If you leave the PC connected to the UPS, it'll continue to draw a little bit of power unless you unplug it or turn off the switch on the power supply in the back of the case. I also recommend against plugging printers and scanners into a UPS because of the potential for draining the power, especially if the printer/scanner is on and the power goes offline when you're not home. Plug printers and scanners into surge protectors, which are plugged into mains power.

If a power outage lasts more than a day or two it's likely that the UPS will run out of juice. But if most power outages you experience are short term, a UPS is a worthwhile investment to keep your primary means of communication open.


* ISPs have their equipment on massive battery backups and/or backup generators, so they often stay online during power outages. ASSuming that the cables haven't been knocked down, you can usually get online if you have backup power.

Monday, January 01, 2007

Thoughts on Selecting .22 Rimfire Ammunition

Most preparedness-minded people will have a least one .22 around. They are excellent for small game hunting, target practice, plinking, training new shooters, vermin control, and can be pressed into use for defense. However, many people fail to properly select the best ammunition for their .22s, focusing instead on price alone. In this post I'll discuss some criteria for selecting the best .22 ammo, focusing on .22 Long Rifle.

Rifles and pistols chambered for .22 Long Rifle can safely chamber and fire the following cartridges:

  • .22 BB Cap (mostly unavailable)
  • .22 CB Cap (available in both Short and Long cases)
  • .22 Short
  • .22 Long (No longer very common)
  • .22 Long Rifle in both standard velocity (subsonic) and high-speed.
  • .22 LR Shot (I haven't tried these so won't comment further.)

There are "hyper velocity" .22 LRs like CCI Stingers and Velocitors, and Remington Yellow Jackets and Vipers. Conversely, there are standard velocity rounds intended for hunting, e.g., CCI Subsonic HPs and Aguila Sniper Subsonics. The latter is a .22 LR length round, but loaded with a heavy 60 grain bullet in a .22 Short case.

Most .22 LR semiautos will function only with Long Rifles. The other rounds won't have enough power to function the action. The Remington Model 572 is a notable exception, being designed to function with Shorts, Longs, or Long Rifles. Sometimes, manually operated repeaters won't function with anything other than LRs either. However, they'll work as a single shot if you load the round directly into the chamber.

Standard velocity rounds, especially hollowpoints or solids which have been flatnosed, work well for small game hunting with good shot placement. They are quieter than high speed loads and often are more accurate.

For controlling vermin larger than rats, high speed or hyper velocity hollowpoints work better than standard velocity loads, except for the Aguila Sniper Subsonics. .22 LR can be used on varmints up to the size of woodchucks and racoons, but shot placement is key. I've seen a rabid raccoon that weighed about 15 lbs absorb over a half dozen high speed hollowpoints PLUS 5 standard velocity solids without expiring. These were all hits in the chest cavity from no more than 10 - 15 yards. A shot through the brain was required to finally kill it.

Small vermin such as rats can be taken care of with standard velocity loads, .22 Shorts, or even CB Caps. I have a couple of boxes of CCI .22 CB Longs that I keep around in case this is necessary. Fired from a rifle, they are about as noisy as an airgun. In other words, pretty darn quiet.

While it's better than nothing, a .22 is not a good choice for defense against people. It simply doesn't have enough bullet mass to reliably stop an aggressor. See my comments about the rabid raccoon above. The light weight, relatively low velocity bullets don't pack enough punch to reliabily penetrate to an attacker's vitals and cause enough damage to force him to stop. That said, high velocity solids would be my choice if I needed to use a .22 for defense; the specific load I'd want would be CCI Mini Mag solids for both its relatively good penetration and CCI's high quality. The only time I'd recommend a .22 for a defensive gun would be for someone who can't handle anything bigger. But, if push came to shove in a worst case scenario, and a child needed to help defend the homestead, then something like a 10/22 with a full load of Mini Mags beats a sharp stick.

The best accuracy will almost always be obtained with some kind of .22 LR ammo. When fired in a LR chamber, bullets from .22 Shorts have a long jump from the case to the rifling, which hurts accuracy. The rounds that a given gun will shoot the most accurately can only be determined by trying a variety of ammo. I recommend buying a 50 round box or two of several kinds of ammo and shooting them at a paper target from a bench, to see what the gun likes best. Shoot at least a couple of targets, at least one of them at 50 yards, to see how individual loads work at a distance.

Shooting for accuracy out to 50 yards is especially important with the Aguila Sniper Subsonics. The heavy 60 grain bullets pack a wallop but are often unstable in .22 rifles with the standard 1-in-16" rifling twist. Since they are somewhat expensive, it's a good idea to test a box to see if they'll shoot acceptably in your gun before acquiring a substantial quantity.

In my experience, the most uniformly accurate and high quality .22 LR ammo (other than specialty target loads like Eley Tenex) is made by CCI. I used to favor Winchester PowerPoints, but had several duds in one brick. I've never had a CCI .22 fail to go off. CCI Mini Mags and Subsonic Hollowpoints function well and shoot accurately in all of the .22s in which I've tried them, including a Ruger 10/22. Savage Mark IIGL, S&W Model 18, Ruger Single Six, and a Winchester 9422.

I recommend storing rimfire ammo in an airtight ammo can, either a GI surplus can or something like an MTM Sportsman's Dry Box. Rimfire ammo is not as well sealed against moisture penetration as centerfire ammo, and if the ammo gets wet or is exposed to humidity for a long time it may go bad.

Hopefully this post has given you some food for thought regarding .22 rimfire ammunition selection. Please share your insights in the comments.

Wednesday, December 27, 2006

Got another Ruger Mini-14

(Cross-posted from Blog O'Stuff.)
It was cold and windy today so I didn't feel like hitting the range. I did however, go up to Surplus City with a couple of guns which I haven't shot in quite awhile, and did some trading. In exchange for my EMF/Rossi Hartford Model 1892 and my Ruger GP-100, plus some boot, I picked up a used stainless steel Ruger Mini-14 GB. It's a 186-series piece. It came with one Ruger factory mag (stainless, no less) and I bought two more Ruger factory mags, both used. (I figure I should get as many evil high capacity magazines as I can while the getting is still good.)

The GB or Government Model differs from the standard Mini-14 with the addition of a flash suppressor screwed onto the muzzle, and a winged front sight several inches back. The front sight block also has a bayonet lug, and the gun will accept standard M-16 bayonets. (Raspberries to Senator Feinstein and her partners in crime.) The GBs were never intended to be sold directly to the public by Ruger, but a fair number of them have become available as police or prison guard trade-ins, as many departments "upgrade" by replacing their Mini-14s with AR-15s.

I really like Mini-14s. They are not as accurate at AR-15s (at least without serious tuning) but they are very simple, ergonomic, and reliable little rifles. Mini-14s are accurate enough for their intended purposes -- potting varmints around a farm or as a social carbine out to a couple of hundred yards.

Getting back to the reliability aspect -- Mini-14s are much less finicky when it comes to maintenance or quality ammo than AR-15s. For example, Wolf .223 doesn't run well in my Colt AR-15A3, but runs just fine in my 182-series Mini-14. I expect it to work fine in the GB. A couple of features which help the Mini-14's reliability are (a) the fact that it taps more than enough gas from the barrel to work the action, and (b) fouling stays out of the action. IOW, it doesn't have the "shits where it eats" problem of the AR-15. Note that the AR-15's direct-impingement (DI) gas system can be reliable, but it demands more cleaning, and that more recent military rifle designs all use pistons, not DI.

One of my online friends used a stainless Mini-14 in Alaska for many years, taking a large number of deer and other game with it. It stood up to harsh conditions well and he still has the rifle, now that he's retired to WV. .223 isn't really a deer caliber but it will do if you take your time and place the bullets right. Perhaps surprisingly to guys in the lower 48, but the Mini-14 is one of the most popular bush guns in AK. It and it's ammo are light. It's reliable and easy to maintain, and has minimal recoil, so a lot of Alaskan natives like it. A stainless Mini-14 in a plastic stock would be a heck of a good choice as a defensive carbine, especially if you need one to keep on a boat.

Sunday, December 17, 2006

FCC Drops Morse Code Requirment for Ham Radio

The FCC is finally dropping the Morse code (AKA "CW") requirement for all classes of amateur radio license. The official license is here (PDF document). The international governing body for amateur radio dropped the requirement several years ago, and several countries had already followed suit, e.g., Germany and Italy, IIRC.

IMHO, this is a good thing. CW is a mode of operation, not a guarantee that someone isn't a schmuck. Yes, CW is useful and I'm glad that portions of the bands are still reserved for CW. But not everyone is interested in it, and many people just cannot learn it even with a lot of study. I've spoken with several General Class hams who've not used it since getting their license. Operators will still need to pass the written exams on radio technology and proper operating procedures before getting a licence.

One reason many hams didn't want the code requirement dropped is because CW can get through poor conditions better than voice on AM or Single Side Band. However, there are new operating modes, such as PSK-31, which use as little bandwidth as CW, perhaps even less, so they work as well in adverse conditions as CW. (I'm especially interested in PSK-31 since it's a way to bridge my interests in computers and radio.)

Time for me to start studying for the Element 3 exam.

Wednesday, December 06, 2006

In Praise of the Non-Tactical Pocketknife

For most of the past 10 years my pocketknife has been a "tactical" folder. First, it was a Spyderco Delica. When I lost the Delica (found it 3 months later) a few years ago, I replaced it with a Benchmade Griptilian. I've been very happy with both knives. They are well made, hold a nice edge, lock securely, and need only one hand to open.

Last weekend I dug out my old Victorinox Pioneer Swiss Army Knife (SWAK). I've had this since sometime in the early '80s. Unlike the current production silver-colored Pioneers the aluminum handle scales on mine have a red oxide finish. It has a spear point blade, bottle opener, can opener, large and small screwdriver blades, a wire stripper notch on the bottle opener, a reamer/awl, and a key ring. It's the same as the real issue SWAK or "Soldier," with the exception of the key ring. Picking up the Pioneer felt like getting reacquainted with an old friend.

I carried my SWAK for years. It accompanied me on a six week trip to Europe in 1984, following me behind the Iron Curtain into Hungary and Yugoslavia and back. I've used it to cut stuff, tighten and loosen screws, pop open sodas and beers, and poke holes in things with the reamer. In other words, it can do a lot more than a knife with only a blade.

My job is in an office pushing bits and bytes around. Dress is business casual. I'd look goofy with a multitool on my belt. Like it or not, fashion can influence knife choice. (And I'm hardly a fashion plate.) And as for tacticality, the closest I have to training in knfe fighting is a semester of fencing in college, close to 20 years ago.

So, Sunday I checked the edge (still shaving sharp after a few years languishing in the handlebar bag on my mountain bike, out in a shed) and sprayed out some dust with some Superlube dry teflon lubricant from a can, and since then I've been carrying the Pioneer instead of my Benchmade. It fits nicely in my pocket like it belongs there and offers more functionality than the Griptilian. The only real advantage the latter has is one-hand opening.

I'm liking having my old friend with me once again. I may even order another one or two to stash away for the future or in an emergency kit.

Monday, December 04, 2006

Power Failure

Getting my ham radio setup with a battery backup came not a moment too soon. Friday night, the power went out.

Last Friday we had a cold front come through, bringing with it high winds. About 2030, the wind blew one of the trees in our yard into the power line feeding us from the pole. Sparks, pops, and groaning noises followed and the power went out.

Out came the flashlights, candles, and my D-cell powered Coleman flourescent lantern.

My wife called PECO and reported the outage. We use Vonage for our phone service and my home LAN is on two APC UPSes so we had phone service and cable modem Internet access until I shut them off to conserve power. In the meantime, we had our cell phones if we had needed to call anyone.

At about 2200 - 2230 we got some power back. A couple of the circuits came back but we had no power upstairs in our bedrooms, nor for the heater (natural gas but the blower requires electric). If things had gone on longer than they did we could still use our gas fireplace, however. Fortuitously, the refrigerator was on a circuit with power.

Meanwhile, I spent some time on the radio and caught the tail end of a Skywarn net. The PowerGate/gel cell setup worked perfectly. I'd done a test run on battery power last Thursday night when I checked into the MARC club net, and got good signal reports.

Saturday morning at about 0930 PECO tech came out. He went and looked at the pole and saw a mass of vegetation which had grown up along it, and that the insulators separating the three feed lines were broken. Due to the vegetation he needed to call for a crew to come out, climb the pole, and defoliate, then fix the connection. (A crew was out over the Summer clearing vegetation away from the wires and pole in my neighbor's yard but apparently they didn't get enough.)

The reason we had some power was that we were getting 110V into the house, not the full 220V. He jumpered the live 110V part to the other part, so we at least had 110V throughout the house, enough to run our heater.

An hour and a half later the crew showed up. They ended up replacing the line from the pole to our house, but I'll need to have an electrician replace the feeder line from the head to the service. (Good thing I have a close friend who's a master electrician.) However, they had to shut power back off for a few hours while they worked. We were back to status quo ante around 1500 Saturday.

Yesterday I went and pruned the tree which had swayed into the line. I'm hoping the reduced wind load will make it steadier. If it does sway or fall it shouldn't take out the power, however, since the PECO crew Saturday rerouted the line. It will drop the currently-unused Verizon phone line, and the heavily-used Comcast cable line, so I do want the tree removed fairly soon.

Wednesday, November 29, 2006

WMR PowerGate 40 Backup Power System

A major reason I got my ham ticket was because I wanted emergency communications. I have a pretty good home setup for VHF/UHF in the form of a Yaesu FT-7800R hooked up to a Comet GP-3 antenna on my roof. What I haven't had, up until now, is some form of powering the radio if the power goes out.

Early last week I placed an order with West Mountain Radio for a few items:

  • A PWRGate PG40 backup power system.
  • An MK brand 73 amp hour gel cell.
  • Cables to connect the PowerGate to my Yaesu power supply and to the gel cel, along with my FT-7800R and VX-5RS HT.

The PG40 and cables came the next day but the gel cel didn't arrive today; it's dropped shipped from the manufacturer's warehouse.

The PWRGate has three power connectors:

  • Power in from a DC power supply, which in turn is plugged into mains power.
  • Power out to the radio.
  • Power to the battery for a trickle charge. This port also accepts power in from the battery.

The connectors are Anderson Power Poles.

During normal operation with mains power, the PWRGate provides a trickle charge to the gel cel and DC to the radio. If the battery drains down it could take a few days to recharge once mains power returns, so at some point I'll get a separate battery charger.

If the mains power goes out then the PWRGate's internal switch reconfigures the unit to take power from the battery and provide it to the radio. The power source transfer is seamless, requiring no user intervention, and when I tried it out I didn't notice any difference in the audio I was listening.

The reasons for using a gel cel are that (a) they're safer than lead acid batteries that you need to worry about keeping equalized since they are maintenance free, and (b) they are rated as spill-proof and don't give off fumes. Being a deep cycle battery, it can safely be discharged down to a low level without harm.

Here's a pic of my setup:




The PWRGate is the finned black thing sitting on top of another black box, which is my DC power supply. The leftmost cord plugged into the top is the power input, the middle is power to the radio, and the right hand one goes to the gel cel. The black square on the red cable to the cel's positive lead is a fuse holder. (I have a temporary cover over the gel cel as a protective measure so nobody accidentally shocks himself.)

Future refinements to this system will include a battery box to protect the gel cel and anybody who get a bit careless, a battery charger, and a cable with Anderson Power Poles on one end and a cigarette lighter receptacle on the other so I can power 12V devices including charging cell phones.

Tuesday, November 21, 2006

Backup Radio Power

The major thing missing from my ham radio setup has been a backup power source. With Winter just around the corner I decided that it was time to remedy this. Today I placed an order with West Mountain Radio for several items:

  • PWRgate 40 package
  • 73 ah gel cell
  • Cable for my VX-5RS
  • Cable for my FT-7800R

The cables have an Andersen Power Pole connector on one end, for plugging into the PWRgate, and the appropriate connector on the other end for plugging into the radio.

The PWRgate allows one to create an uninterruptable power supply for radios. Ugly ASCII diagram:



[A/C power] – [PWRgate] – [Gel cell]
|
|
[Radio]

This provides the same basic functionality as a UPS intended for computers. If the mains power goes out an you're using the radio, it will automatically shift over to the gel cell. While the radio isn't being used, it will trickle charge the battery.

My Yaesu FT-7800R consumes only 0.5A in RX mode (squelched) and 8.5A when transmitting, so if I'm just monitoring during a power outage, the 73 ah gel cell should last quite awhile. My VX-5RS HT uses a max of 1.9A when transmitting, so it'll last even longer.

At some point I may invest in a generator but for now our power is sufficiently reliable that I don't feel the need yet.

Monday, November 20, 2006

Cross-platform encryption

I want to save digital copies of important documents on a USB stick, but want to secure them against unauthorized access if the drive gets into the wrong hands, because it would be an identity thief's wet dream. The stick will be part of my household emergency kit.

Today I discovered jFileCrypt, a cross-platform encryption/decryption tool written in Java, and which can run on any platform with Java 5. Aside from the fact that it's free (GPL) software, being platform-independent is what I really find attactive. JFileCrypt supports Blowfish so the resulting encrypted file should be secure.

Alternatives include Mac OS X's built-in ability to create encrypted disk images and GPG. Unfortunately, an ecrypted Mac disk image isn't cross platform, and GPG can be confusing, although I've been playing around with it and I'm getting a better understanding of it. For Windows and Linux users, TrueCrypt looks like a good alternative.

Ideally, I'd like to have an ~500 MB encrypted file or folder on a 1 GB USB drive. On the unencrypted portion I'll keep a copy of the encryption utility so that if necessary, I can decrypt the information even if I don't have access to one of my computers. The password I'll be using is long, non-obvious, and has zero significance to anyone other than me.

If any of my readers have suggestions for cross-platform encryption software that would be suitable for this application, please post them as a comment.

Wednesday, November 15, 2006

Good 2M Propagation Tonight

So I'm sitting here in Plymouth Mtg., PA scanning through the freqs on my radio and I picked up the Carbon County ARES net coming in loud and clear. Their repeater is located about 60 miles away in Jim Thorpe, PA. I checked in and introduced myself. Net control gave me a good signal report, even though I was transmitting with only 10W. According to him, there were some "scrambled eggs" in the background but I was totally intelligible.

Even though VHF FM is often said to require line of sight, there are a lot of hills between the repeater and me, so I think the knife edge effect is in play.

My rig is a Yaesu FT-7800R 2M/70cm dual bander, with a Comet GP-3 antenna on top of a 5 foot mast on the short chimney sticking out of my roof.

A few minutes later a station from Sussex County, DE checked in and reported that he too was hearing the repeater clearly. He noted that he also was able to bring in Martinsburg, WV shortly beforehand. Impressive!

Nice to know I can communicate out that far without much infrastructure (or will be, once I get a battery backup in place for my shack).

Tuesday, November 14, 2006

When the lights go out

Back in August I posted about coming shortfalls in reliable electrical power.
...

The [Electric Reliability Organization] projects that U.S. demand will increase by 141,000 megawatts (MW) over the next 10 years. Supply, however, will increase by only 57,000 MW, and that assumes that all currently proposed new facilities are approved and built.

The system will be operating below the marginal capacity needed to ensure supply reliability at all times. In other words, in peak periods like heat waves, there won’t be enough electricity to go around. Blackouts will inevitably result.

...

Read the rest of the article here. [H/T to InstaPundit.]

Now, it won't be the end of the world if this comes to pass. However, reliable electricity is something that most Americans have come to expect as a given, much as if it was air. It will take getting used to, and points to the value of implementing alternatives for when grid power is down.

Thursday, October 26, 2006

NRA Survival Toolkit

I got one of these last week. It contains a Blastmatch fire starter, a couple tinder cubes, a whistle, and a signal mirror. It's packed inside a Pelican-type plastic case. There's some foam padding in there that's unneeded IMO, so I plan to remove it to add additional items. E.g. a pill bottle filled with vaseline impregnated cotton balls for use as tinder.

For the price it's a steal. The Blastmatch alone normally goes for what the kits lists for. Even though it's at the NRA Store, AFAIK you do not need to be an NRA member to order from them. (That said, JOIN THE NRA if you haven't already.)

Sunday, September 24, 2006

Outdoor Products Power Pack

After last week's fun in center city Philadelphia I decided it was time to redo my get home bag (GHB). My GHB is actually my laptop bag, so it needs to securely hold my G4 iBook in addition to providing room for normal GHB stuff. I've been using an REI Big Byte computer backpack but wanted something a bit larger with better designed pockets.

Yesterday I went to REI and bought an Outdoor Products Power Pack in black. I used Outdoor Products backpacks in high school, college, and law school as book bags and was not nice to them. They shrugged off all the mistreatment I dished out and were no worse for the wear, except for getting dirty. The bag I used in law school is now the GHB in my truck.

Anyway, the Power Pack seems well made like my older bags. The pockets are well designed for a laptop bag and there's plenty of room to carry survival and first aid supplies. The shoulder straps are well padded, as is the back, and there's a sternum strap for long hauls. There's a mesh bottle pocket on the side which will hold a 32 oz. Nalgene. On front there's a place to stash a jacket, held in place with mesh and straps with a Fastex buckle.

It's not tacticool but it looks like a good choice for those of us stuck working in the city.

Thursday, September 21, 2006

Minor SHTF in Philly Today

We experienced a minor SHTF event today in Philadelphia due to an electrical fire and explosion on south 15th Street, very close to City Hall. I work in a high-rise at 15th & Market, right near the epicenter. I later found out that a 36-square block area was closed off to traffic and about 5,000 people had to evac the immediate area.

Around 1300 we heard a kaboom. For the next 10 - 15 minutes everyone was wondering what had happened. At about 1315 the message was passed to evacuate the building. For some reason the fire alarm was not activated nor was the building’s P.A. system used. Rather, the floor captains were telling everyone to leave. They have Blackberries to send and receive text messages in emergencies.

Shortly after the kaboom I grabbed my stuff and made to ready to evacuate in case the order was given. I got my jacket and bag ready and shutdown one of my PCs. So, when we finally were told to leave all I had to do was to close my laptop and put it in my bag, put on my jacket, and go.

A few things disturbed me about how the whole thing was handled and I intend to (nicely) speak to our HR person tomorrow. First, within a few minutes of the kB, I saw one of our floor captains leaving the building. Considering that it’s a floor captain’s job to make sure that everyone is out, I regard this as abandoning her post. Her panicked reaction demonstrates that she’s unsuited for the role.

Our other floor captain performed his job but left his emergency bag behind, which he immediately regretted. The floor captains’ emergency bags contain stuff like a hard hat, megaphone, flashlight, etc.

Also, although we had fire drill on Tuesday, today’s event was a real cluster. Communication was fragmented, nobody responsible thought to activate the fire alarm, and no use was made of the building’s P.A. system. When people were told to leave the building they weren’t told where to go until after milling around outside for about ten minutes.

Natually, the rumors started flying immediately. The first was that the boom was due to a gas leak, and it wasn’t for awhile that we heard the true cause.

I carry some basic survival supplies in my bag: water bottle, a snack bar, small first aid kit, bandanna, Gerber Multiplier, chemlight, Princeton Tec LED flashlight, poncho, and a space blanket. I’m strongly considering adding my Yaesu VX-5RS ham radio which has wide-band receive, although I've learned that Philadelphia recently implemented a trunked Motorola system for the police and fire departments, so I'm not sure how useful it would be.

Monday, September 18, 2006

Preps to keep in your vehicle

Having just returned from an overnight trip to Arlington, VA, I am prompted to discuss things that should be kept in a vehicle to help deal with emergencies on the road. The possibility always exists that you’ll run into a mechanical failure which requires dealing with, or outside emergencies. Keeping a bag or box in your trunk or behind the seat of a pickup can make life a lot easier in the event of an inconvenience, or save a life in an emergency.

For dealing with mechanical issues I keep several items in my truck:

  • Some basic hand tools

  • A spare quart of motor oil

  • A jug of antifreeze

  • A jug of windshield wiper fluid

  • A D-cell flashlight

  • The factory jack

  • A can of WD-40

  • A few shop rags, a roll of paper shop towels, and waterless hand cleaner wipes

  • Jumper cables

  • A few magnesium road flares

  • 12VDC air compressor/flashlight

  • A can of Fix-A-Flat
  • Four-way tire iron

To deal with other issues I add:

  • A Kershaw lock blade knife

  • A Gerber Multiplier Scout multitool

  • CB radio (also handy for real-time traffic reports)

  • My everyday carry cell phone

  • First aid kit

  • Rain poncho

  • Space blanket
A lot more stuff could be added, and this list would be expanded if I didn't live in a large metro area.

Out trip remained within heavily-travelled areas so I wasn’t worried about taking anything for an overnight stay in the boonies, like the BOB shown in this post.

I normally also carry a get-home bag with additional supplies including an MRE, water, another poncho, compass, etc. but had to take it out for this trip since we were short on space. I need to change some of the contents and downsize it into a smaller bag. That will be a project for a future post.